Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 354 | Manualshive

Страница: 354 / 444

background image

Show Commands

Page 354

7750 SR OS Interface Configuration Guide

Unicast Packets

Input/Output

The number of packets, delivered by this sub-layer to a higher (sub-)
layer, which were not addressed to a multicast or broadcast address at
this sub-layer. The total number of packets that higher-level protocols
requested be transmitted, and which were not addressed to a multicast
or broadcast address at this sub-layer, including those that were dis-
carded or not sent.

Multicast Pack-

ets Input/Output

The number of packets, delivered by this sub-layer to a higher (sub-)
layer, which were addressed to a multicast address at this sub-layer.
For a MAC layer protocol, this includes both Group and Functional
addresses. The total number of packets that higher-level protocols
requested be transmitted, and which were addressed to a multicast
address at this sub-layer, including those that were discarded or not
sent. For a MAC layer protocol, this includes both Group and Func-
tional addresses.

Broadcast Pack-

ets Input/Output

The number of packets, delivered by this sub-layer to a higher (sub-)
layer, which were addressed to a broadcast address at this sub-layer.
The total number of packets that higher-level protocols requested be
transmitted, and which were addressed to a multicast address at this
sub-layer, including those that were discarded or not sent.
For a MAC layer protocol, this includes both Group and Functional
addresses.

Discards Input/

Output

The number of inbound packets chosen to be discarded to possibly
free up buffer space.

Unknown Proto

Discards Input/

Output

For packet-oriented interfaces, the number of packets received via the
interface which were discarded because of an unknown or unsup-
ported protocol. For character-oriented or fixed-length interfaces that
support protocol multiplexing the number of transmission units
received via the interface which were discarded because of an
unknown or unsupported protocol. For any interface that does not
support protocol multiplexing, this counter will always be 0. For
ATM, this field displays cells discarded on an invalid vpi/vci.
Unknown proto discards do not show up in the packet counts.

Errors

For ATM, this field displays the number of cells discarded due to
uncorrectable HEC errors. Errors do not show up in the raw cell
counts.

LLF Admin State

Displays the Link Loss Forwarding administrative state.

LLF Oper State

Displays the Link Loss Forwarding operational state.

Label

Description (Continued)

«
...
352
353
354
355
356
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

Бренд: IBM Страницы: 342

DGE-560T - Gigabit PCI-Express SNMP VLAN Flow Control Network...

Бренд: D-Link Страницы: 53

Бренд: Lancom Страницы: 25

Бренд: Supero Страницы: 112

Бренд: FS Страницы: 19

Бренд: Teletronics International Страницы: 57

SteelCentral AppResponse 2180

Бренд: Riverbed Страницы: 82

Бренд: ZyXEL Communications Страницы: 12

Бренд: Digi Страницы: 75

Ultra WiFi Booster

Бренд: Optus Страницы: 8

Бренд: LevelOne Страницы: 142

Бренд: ORiNG Страницы: 101

Бренд: Valcom Страницы: 3

OfficeConnect 3CXSH654B

Бренд: 3Com Страницы: 52

Бренд: SMC Networks Страницы: 68

Бренд: I-Tech Страницы: 6

Network Video Recorder

Бренд: IC Realtime Страницы: 118

Mobile Network Video Recorder

Бренд: IC Realtime Страницы: 158

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды