Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 233 | Manualshive

Страница: 233 / 444

background image

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 233

Values

0x0600

..

0xffff:

1536 — 65535 (accepted in decimal or hex)

qinq-etype

Syntax

qinq-etype

0x0600..0xffff

no qinq-etype

Context

config>port>ethernet

Description

This command configures the Ethertype used for Q-in-Q encapsulation.

The

no

form of this command reverts the quinq-etype value to the default.

Parameters

0x0600..0xffff —

Specifies the quinq-etype to expect.

Values

1536 — 65535 in decimal or hex formats.

report-alarm

Syntax

[

no

]

report-alarm

[

signal-fail

] [

remote

] [

local

] [

no-frame-lock

] [

lcd

] [

high-ber

]

Context

config>port>ethernet

Description

This command specifies when and if to generate alarms and alarm clear notifications for this port.

Parameters

signal-fail —

Reports an Ethernet signal lost alarm.

remote —

Reports remote faults.

local —

Reports local faults.

no-frame-lock —

Reports a 'not locked on the ethernet framing sequence' alarm.

lcd —

Reports a codegroup delineation error.

high-ber —

Reports a high bit error rate alarm.

single-fiber

Syntax

[

no

]

single-fiber

Context

config>port>ethernet

Description

This command enables packet gathering and redirection of IP packets from a single fiber (RX) port of
the Ethernet or SONET/SDH interface and redistributes packets to other interfaces through either
static routes or policy-based forwarding.

This parameter can be applied in conjunction with the strip-label command. If they are applied
together, the port must have the single-fiber option configured before it can be associated with an
interface that is configured with the strip-label option.

Once a port is configured with single-fiber, traffic will no longer be transmitted out of that port.

«
...
231
232
233
234
235
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

Professional Series

Бренд: PACOM Страницы: 15

Бренд: Panasonic Страницы: 4

Netlink FRX4000

Бренд: Cabletron Systems Страницы: 8

Бренд: Cabletron Systems Страницы: 4

MMAC-Plus 9F106-02

Бренд: Cabletron Systems Страницы: 7

Бренд: DCE Страницы: 5

Бренд: Vivotek Страницы: 170

Бренд: H3C Страницы: 26

Бренд: QNAP Страницы: 39

Fan Tray 8820-S2-900

Бренд: Paradyne Страницы: 6

Бренд: M86 Security Страницы: 309

Turbo NAS TVS-71 Series

Бренд: QNAP Страницы: 51

Бренд: TP-Link Страницы: 57

Бренд: Ubiquiti Страницы: 28

Бренд: F.F. Group Страницы: 56

Бренд: Axis Страницы: 64

Бренд: SHOWTEC Страницы: 15

LN1000 - RELEASE NOTES 8-27-2010

Бренд: Juniper Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды