Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 263 | Manualshive

Страница: 263 / 444

background image

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 263

scramble

Syntax

[

no

]

scramble

Context

config>port>sonet-sdh>path

Description

This command enables SONET/SDH payload scrambling.

Scrambling randomizes the pattern of 1s and 0s carried in a SONET frame. Rearranging or
scrambling the pattern prevents continuous strings of all 1s or all 0s and meets the needs of physical
layer protocols that rely on sufficient transitions between 1s and 0s to maintain clocking.

For ATM, this command enables or disables ATM cell-level payload scrambling/descrambling using
x43+1 polynomial as defined in ITU-T I.432.1. Scrambling is enabled by default for the ATM path/
channel. Note that this scrambling is done in addition to SONET/SDH frame scrambling/
descrambling, which is always enabled in the framer.

The

no

form of this command disables scrambling.

Default

no scramble

signal-label

Syntax

signal-label

value

Context

config>port>sonet-sdh>path

Description

This command sets the C2 byte value. The purpose of this byte is to communicate the payload type
being encapsulated by SONET framing.

Default

0xcf

Parameters

value —

Specifies the C2 byte value, expressed as a decimal integer or a value in hex format.

Values

1 — 254 or 0x01 — 0xfe

trace-string

Syntax

trace-string

[

trace-string

]

no trace-string

Context

config>port> sonet-sdh>path

Description

This command specifies that a J1-path-trace that identifies the circuit is inserted continuously at
source. This can be checked against the expected value by the receiver. If no trace string is entered
then a null string is used.

The

no

form of this command resets the string to its default.

Default

The default J1 value is Alcatel-Lucent XXX YYY (for example, Alcatel 7750 SR) where XXX is the
platform name, such as "7750" or "7450" or "7710", and YYY is the product name, such as "SR" or

«
...
261
262
263
264
265
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

Бренд: D-Link Страницы: 5

Бренд: D-Link Страницы: 2

grandMA2 Series

Бренд: MA lighting Страницы: 36

Бренд: QNAP Страницы: 20

Бренд: TC Electronic Страницы: 174

Бренд: E-TOP Страницы: 76

Бренд: Edgewater Networks Страницы: 7

SUPERLOADER DLT MAGAZINE

Бренд: Tandberg Data Страницы: 6

IPS Pro-Module-24C-GE-BP-TM

Бренд: Trend Micro Страницы: 3

SmartSTACK ELS100-24TXM

Бренд: Cabletron Systems Страницы: 117

Бренд: Ubiquiti Страницы: 20

Бренд: Milesight Страницы: 15

TE100S8P - Fast Ethernet Switch

Бренд: TRENDnet Страницы: 11

GS2020E GigaSPIRE BLAST

Бренд: Calix Страницы: 15

Бренд: Watchguard Страницы: 21

Бренд: ZyXEL Communications Страницы: 348

Бренд: FiberHome Страницы: 44

FiberTwist XGS2420

Бренд: Genexis Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды