Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 151 | Manualshive

Страница: 151 / 444

background image

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 151

IMA Test Procedure

Use the following CLI to perform IMA Test Pattern Procedure on a member link of an IMA
group:

CLI Syntax:

configure# port bundle-

type

-

slot

/

mda

.

bundle-num

multilink-bundle

ima

test-pattern-procedure

test-link

port-id

test-pattern [

pattern

]

no shutdown

An operator can deploy IMA test procedures to verify operations of IMA group and its member
links. Following is a list of key points about the test pattern procedure.

1.

The test procedure is performed as defined by the IMA specification version 1.1, i.e. a test pat-
tern is sent over the specified link and is expected to be looped back over all the links in the
group. ICP cells are used to perform the test.

2.

The test procedure is not traffic affecting, for example, data traffic will not be affected by the
ongoing test.

3.

There can only be a single test executed per an IMA group at any given time

4.

The IMA member link must exist in the specified group for the command to be accepted.

5.

The test-pattern-procedure must be shutdown before a new test-link value or test pattern is
accepted.

6.

The current IMA group test pattern configuration and result of a given IMA test can be seen
by executing a show command for the IMA group. A test-link result can have three values:

a. Disabled: The test-link is currently not running.

b. Operating: The test pattern procedure is

no shutdown

and there are currently no failed-

links for this running test-pattern-procedure.

c. Link-Failed: One or more links have failed the test-pattern-procedure. Execute a

show

port <slot/mda/port.sonet-sdh-index> ima-link

command to see the failed link and

received pattern value.

7.

Deleting a member link that is the same as the specified test-link, to stay in compliance with
key point 4, will result in the test-link value being reset to default.

8.

IMA test procedure configurations are not saved when the admin save command is executed.

«
...
149
150
151
152
153
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

Бренд: D-Link Страницы: 12

Power Xpert Meter 2000

Бренд: Eaton Страницы: 16

POW-R-COMMAND 1000

Бренд: Eaton Страницы: 84

Module NI PXI-8250

Бренд: National Instruments Страницы: 39

Бренд: Quantum Страницы: 20

BIC 1I12-P2A25-M30MI1-BPX05-110

Бренд: Balluff Страницы: 12

Бренд: Lancom Страницы: 70

Бренд: Patton electronics Страницы: 12

Бренд: E-Lins Страницы: 9

Бренд: ZyXEL Communications Страницы: 2

SmartSwitch 8-slot

Бренд: Cabletron Systems Страницы: 150

Бренд: XtendLan Страницы: 52

Бренд: Firetide Страницы: 32

Бренд: Axis Страницы: 64

Бренд: SHOWTEC Страницы: 15

Бренд: Lantech Страницы: 23

Бренд: Billion Страницы: 16

Бренд: Laguna Tools Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды