manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса, Страница: 373 / 444

Поделиться
Скачать
Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 373

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 373

Sample Output

A:ALA-2934 show mda 7/2 detail (ATM MDA)

========================================================================== 

MDA 7/2 detail 

========================================================================== 

Slot Mda  Provisioned          Equipped             Admin    Operational 

          Mda-type             Mda-type             State    State 

-------------------------------------------------------------------------- 

7    2    m4-atmoc12/3-sfp     m4-atmoc12/3-sfp     up       up 

MDA Specific Data 

    Maximum port count            : 4 

    Number of ports equipped      : 4 

    Transmit timing selected      : CPM Card B 

    Sync interface timing status  : Qualified 

    Network ingress queue policy  : default 

    Capabilities                  : Sonet, ATM 

    Min channel size              : Sonet STS-12 

    Max channel size              : Sonet STS-12 

    Max number of channels        : 4 

    Channels in use               : 0 

Egress RT-VBR

Indicates the total real-time variable bit rate (rt-VBR) bandwidth con-
sumed on this interface in the egress direction.

Ingress NRT-VBR

Indicates the total non-real-time variable bit rate (nrt-VBR) bandwidth 
consumed on this interface in the ingress direction.

Egress NRT-VBR

Indicates the total non-real-time variable bit rate (nrt-VBR) bandwidth 
consumed on this interface in the egress direction.

Ingress UBR

Indicates the total unspecified bit rate (UBR) bandwidth consumed on 
this interface in the ingress direction.

Egress UBR

Indicates the total unspecified bit rate (UBR) bandwidth consumed on 
this interface in the egress direction.

Ingress Total

Indicates the number of valid ATM cells received by the ATM interface 
including both CLP=0 and CLP=1 cells. If traffic policing is imple-
mented, then cells are counted prior to the application of traffic polic-
ing.

ATM Link Band-

width

Indicates the total ATM link bandwidth accepted on this interface.

Shaped Bandwidth

Indicates the total shaped bandwidth consumed on this interface in the 
egress direction.

HEC Errors 

(Dropped)

Indicates the number of cells with uncorrectable HEC errors on this 
interface.

HEC Errors 

(Fixed)

Label

Description  (Continued)

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов