Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 244

Страница: 244 / 444

Configuration Commands

Page 244

7750 SR OS Interface Configuration Guide

egress

Context

config>port>ml-bundle>mlppp

Description

This command enables the context to configure egress MLPPP QoS profile parameters for the
multilink bundle.

Default

none

ingress

Context

config>port>ml-bundle>mlppp

Description

This command enables the context to configure ingress MLPPP QoS profile parameters for the
multilink bundle.

Default

none

qos-profile

Syntax

qos-profile

profile-id

no qos-profile

Context

config>port>ml-bundle>mlppp>egress

Description

This command specifies the egress QoS profile to be used for the outgoing traffic over this MLPPP
bundle.

The

form of the command removes the parameters from the configuration.

profile-id —

Specifies the egress QoS profile to be used for the outgoing traffic over this MLPPP

bundle. The value can only be modified if the bundle is shutdown.

Values

1 — 128

endpoint-discriminator

Syntax

endpoint-discriminator class

{

ip-address

global-mac-address

} [

discriminator-id

discriminator-id

]

no endpoint-discriminator

Context

config>port>ml-bundle>mlppp

Description

This command configures the endpoint-discriminator class and ID. The port must be shutdown to
modify command parameters.

The

form of the command removes the parameters from the configuration.

Parameters

class —

Specifies the Link Control Protocol endpoint descriminator class field type.

Содержание 7750 SR OS





























































































































































































































































































































































































































































Результаты поиска

Содержание 7750 SR OS

Отзывы:

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса, Страница: 244 / 444

Результаты поиска

Содержание 7750 SR OS

Отзывы: