Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 259

Страница: 259 / 444

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 259

Default

none

Parameters

sts3 —

Configures STS3/STM1 payload as clear channel.

tu3 —

Configures STS3/STM1 payload as Tributary Unit Group 3 (TUG3).

ds3 —

Configures the port or channel as DS-3 STS1/VC3 payload as DS-3.

e3 —

Configures the port or channel as E-3 STS1/VC3 payload as E-3.

vt2 —

Configures the path STS1 payload as vt2 as a virtual tributary group. Only allowed on STS-1

nodes. (SONET VT container)

vt15 —

Configures the path as a virtual tributary group. Only allowed on STS-1 nodes. (SONET VT

container)

ds1 —

Configures the port or channel as DS1.vt15 or vt2 payload as DS-1

e1 —

Configures VT2 payload as E-1.

report-alarm

Syntax

[

]

report-alarms

[

pais

] [

plop

] [

prdi

] [

pplm

] [

prei

] [

puneq

] [

plcd

]

Context

config>port>sonet-sdh>path

Description

This command enables logging of SONET (SDH) path alarms for a SONET-SDH port. Only path
alarms can be configured in the channel context.

The

form of this command disables logging of the specified alarms.

Parameters

pais —

Reports path alarm indication signal errors. When configured,

pais

alarms are raised and

cleared.

Default

pais

alarms are not issued

plop —

Reports path loss of pointer (per tributary) errors. When configured,

plop

traps are raised but

not cleared.

Default

plop

traps are issued

prdi —

Reports path remote defect indication errors. When configured,

prdi

alarms are raised and

cleared.

Default

prdi

alarms are not issued

pplm —

Reports a path payload mismatch, as a result the channel will be operationally downed.

When configured,

pplm

traps are raised but not cleared.

Default

pplm

traps are issued

prei —

Reports a path error condition raised by the remote as a result of b3 errors received from this

node. When configured,

prei

traps are raised but not cleared.

Default

prei

traps are not issued

puneq —

Reports path unequipped errors. Reports path unequipped signal errors.

Default

puneq traps are issued

Содержание 7750 SR OS





























































































































































































































































































































































































































































Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса

Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды