Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 436

Страница: 436 / 444

Debug Commands

Page 436

7750 SR OS Interface Configuration Guide

lag

Syntax

lag

[

lag-id

lag-id

[

port

port-id

]] [

all

]

lag

[

lag-id

lag-id

[

port

port-id

]] [

] [

pkt

] [

cfg

] [

red

] [

iom-upd

] [

port-state

] [

timers

] [

sel-

logic

] [

mc-pkt

]

no lag

[

lag-id

lag-id

]

Context

debug

Description

This command enables debugging for LAG.

Parameters

lag-id —

Specifies the link aggregation group ID.

port-id —

Specifies the physical port ID.

Syntax

slot/mda/port

channel

]

sm —

Specifies to display trace LACP state machine.

pkt —

Specifies to display trace LACP packets.

cfg —

Specifies to display trace LAG configuration.

red —

Specifies to display trace LAG high availability.

iom-upd —

Specifies to display trace LAG IOM updates.

port-state —

Specifies to display trace LAG port state transitions.

timers —

Specifies to display trace LAG timers.

sel-logic —

Specifies to display trace LACP selection logic.

mc —

Specifies to display multi-chassis parameters.

mc-packet —

Specifies to display the MC-LAG control packets with valid authentication were

received on this system.

ppp

Syntax

[

]

ppp

port-id

Context

debug

Description

This command enables/disables and configures debugging for PPP.

Parameters

port-id —

Specifies the physical port ID

Syntax:

port-id

slot/mda/port[.channel]

aps-id

aps-

group-id

channel

]

aps

keyword

group-id 1 — 64

bundle IDbundle-

type

slot/mda

bundle-num

bpgrp-

type

bpgrp-num

bundle keyword

Содержание 7750 SR OS





























































































































































































































































































































































































































































Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса

Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды