Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 433

Страница: 433 / 444

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 433

application —

Dumps the specified application information that was synchronized with the multi-

chassis peer.

Values

dhcps, igmp, igmp-snooping, mc-ring, srrp, sub-mgmt, mld-snooping, all

detail —

Displays detailed information.

alarm-deleted|local-deleted —

Filters by entry type.

srrp-sync-data

Syntax

srrp-sync-database

[

instance

instance-id

] [

peer

ip-address

]

Context

tools>dump>redundancy>multi-chassis

Description

This command dumps multi-chassis SRRP sync database information.

Parameters

instance-id —

[1..4294967295]

ip-address —

Dumps the specified address (in the form of a.b.c.d).

ima

Syntax

ima

Context

tools>perform

Description

This command allows the use of IMA operations.

reset

Syntax

reset

bundle-id

Context

tools>perform>ima

Description

This command sets an IMA-bundle to the Start Up state.

Parameters

bundle-id —

Specifies an existing bundle ID.

Values

bundle

ima

slot/mda.bundle-num

bundle-num —

[1..256]

Содержание 7750 SR OS





























































































































































































































































































































































































































































Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса

Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды