Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 444

Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 85

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 85

802.1x Basics

Figure 21: 802.1x Architecture

The IEEE 802.1x standard defines three participants in an authentication conversation (see

):

•

The supplicant — This is the end-user device that requests access to the network.

•

The authenticator — Controls access to the network. Both the supplicant and the
authenticator are referred to as Port Authentication Entities (PAEs).

•

The authentication server — Performs the actual processing of the user information.

The authentication exchange is carried out between the supplicant and the authentication server,
the authenticator acts only as a bridge. The communication between the supplicant and the
authenticator is done via the Extended Authentication Protocol (EAP) over LANs (EAPOL). On
the back end, the communication between the authenticator and the authentication server is done
with the RADIUS protocol. The authenticator is thus a RADIUS client, and the authentication
server a RADIUS server.

OSSG038

Client

Alcatel 7450 ESS

RADIUS

Authentication

Server

Supplicant

EAPOL

RADIUS

Authenticator

Authenticator

Server

7750 SR

«
...
83
84
85
86
87
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов