Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 195

Страница: 195 / 444

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 195

hsmda-scheduler-overrides

Syntax

[

]

hsmda-scheduler-overrides

Context

config>card>mda>ingress

Description

This command enables the context to configure ingress HSMDA scheduler policy overrides.

The

form of the command returns the default values.

Default

none

max-rate

Syntax

max-rate

rate

no max-rate

Context

config>card>mda>ingress>hsmda-scheduler-override

Description

This command configures the explicit maximum frame-based bandwidth limit. This object overrides
values specified in the

config>qos>hsmda-scheduler-policy>max-rate

context.

The

form of the command returns the

rate

value to the default value.

scheduling-class

Syntax

scheduling-class

class

rate

rate

scheduling-class

class

weight

weight-in-group

no scheduling-class

class

Context

config>card>mda>ingress>hsmda-scheduler-override

Description

This command configures scheduling class override parameters.

Parameters

class —

Identifies the scheduling class to be being overridden.

Values

1 — 8

rate

rate

—

Overrides the HSMDA scheduler policies maximum rate for the scheduling class and

requires either the

max

keyword or a rate defined in megabits-per-second. In order for the

rate

keyword to be specified, the scheduling class cannot be a member of a weighted scheduling
group as defined on the HSMDA scheduling policy. The

rate

keyword is mutually exclusive with

the

weight

keyword. Also, either the

rate

weight

keyword must be specified.

The

max

keyword removes any existing rate limit imposed by the HSMDA scheduler policy for

the scheduling class allowing it to use as much total bandwidth as possible.

Values

1 — 40000, max (Mbps)

weight

weight-in-group

—

Overrides the weighted scheduler group weight for the scheduling class as

defined in the HSMDA scheduler policy. In order for a weight keyword to be specified, the
scheduling class must be a member of a weighted scheduling group as defined on the HSMDA

Содержание 7750 SR OS





























































































































































































































































































































































































































































Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса

Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды