manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса, Страница: 295 / 444

Поделиться
Скачать
Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 295

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 295

Description

This command specifies the timer, in tenths of seconds, which controls the delay between detecting 
that a LAG is down (all active ports are down) and reporting it to the higher levels.

A non-zero value can be configured, for example, when active/standby signalling is used in a 1:1 
fashion to avoid informing higher levels during the small time interval between detecting that the 
LAG is down and the time needed to activate the standby link.

Default

0

Parameters

down 

hold-down-time

 — 

Specifies the hold-time for event reporting

Values

0 — 2000

lacp

Syntax

lacp 

[

mode

] [

administrative-key

 

admin-key

]

no lacp

Context

config>lag

Description

This command specifies the LACP mode for aggregated Ethernet interfaces only. This command 
enables the LACP protocol. Per the IEEE 802.3ad standard, the Link Aggregation Control Protocol 
(LACP) provides a standardized means for exchanging information between Partner Systems on a 
link to allow their Link Aggregation Control instances to reach agreement on the identity of the Link 
Aggregation Group to which the link belongs, move the link to that Link Aggregation Group, and 
enable its transmission and reception functions in an orderly manner. LACP can be enabled on a 
maximum of 256 ports. 

Default

no lacp

Parameters

mode — 

Specifies the mode in which LACP will operate.

Values

passive

 — Starts transmitting LACP packets only after receiving packets. 

active

 — Initiates the transmission of LACP packets. 

administrative-key 

admin-key

 — 

Specifies an administrative key value to identify the channel group 

on each port configured to use LACP. This value should be configured only in exceptional cases. 
If it is not specified, a random key is assigned.

Values

1 — 65535

lacp-xmit-interval

Syntax

lacp-xmit-interval

 {

slow

 | 

fast

}

Context

config>lag

Description

This command sepcifies the interval signaled to the peer and tells the peer at which rate it should 
transmit.

Default

fast

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов