Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 212

Страница: 212 / 444

Configuration Commands

Page 212

7750 SR OS Interface Configuration Guide

Parameters

mtu-bytes —

Sets the maximum allowable size of the MTU, expressed as an integer.

Values

512 — 9212

Range

config>port>ethernet

512 — 9212

config>port>sonet-sdh>path

512 — 9208

config>port>tdm>ds3

512 — 9208

config>port>tdm>ds1>channel-group

512 — 9208

config>port>tdm>e3

512 — 9208

config>port>tdm>e1>channel-group

512 — 9208

network

Syntax

network

Context

config>port>tdm>ds1>channel-group
config>port>tdm>e1>channel-group

Description

This command enables the context to configure network channel group parameters.

queue-policy

Syntax

queue-policy

name

no queue-policy

Context

config>port>tdm>ds1>channel-group>network
config>port>tdm>e1>channel-group>network

Description

This command specifies an existing network policy to apply to the channel group.

SONET/SDH or TDM

Access

bcp-dot1q

1522

SONET/SDH or TDM

Access

ipcp

1502

SONET/SDH or TDM

Access

frame-relay

1578

ATM, SONET/SDH or TDM

Access

atm

1524

10/100 or 100FX Ethernet

Network

null

1514

10/100 or 100FX Ethernet

Network

dot1q

1518

SONET/SDH

Network

ppp-auto

1524

Type

Mode

Encap Type

Default
(Bytes)

Содержание 7750 SR OS





























































































































































































































































































































































































































































Результаты поиска

Содержание 7750 SR OS

Отзывы:

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса, Страница: 212 / 444

Результаты поиска

Содержание 7750 SR OS

Отзывы: