manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса, Страница: 127 / 444

Поделиться
Скачать
Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 127

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 127

        exit

----------------------------------------------

A:ALA-A>config>port>sonet-sdh#

In order to set the channelized mode on a port, the DS3 parameter must be in a shut down state. 
Clear channel uses out-of-band signaling, not in-band signaling, so the channel's entire bit rate is 
available. Channelized ports use in-band signalling and must be explicitly enabled. 

A:ALA-A>config>port# tdm

A:ALA-A>config>port>tdm# ds3 1.1

A:ALA-A>config>port>tdm>ds3# shutdown

A:ALA-A>config>port>tdm>ds3# channelized ds1

A:ALA-A>config>port>tdm>ds3# no shutdown

A:ALA-A>config>port>tdm>ds3# exit

The following displays the output:

A:ALA-A>config>port# 

info

----------------------------------------------

        sonet-sdh

            path sts12

                no shutdown

            exit

            path sts3-1

                no shutdown

            exit

            path sts1-1.1

                no shutdown

            exit

        exit

        tdm

            ds3 ds3-1.1

                channelized

                no shutdown

            exit

        exit

        no shutdown

----------------------------------------------

A:ALA-A>config>port#

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов