manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса, Страница: 424 / 444

Поделиться
Скачать
Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 424

Show Commands

Page 424

7750 SR OS Interface Configuration Guide

MC Admin Key        : 1                     MC Active/Standby    : active

MC Lacp ID in use   : false                 MC extended timeout  : false

MC Selection Logic  : waiting for peer info MC Config Mismatch  : no mismatch

-------------------------------------------------------------------------------

Port-id        Adm    Act/Stdby Opr    Primary   Sub-group     Forced

Prio

-------------------------------------------------------------------------------

1/1/1          up     active    up     yes       7             -        99

1/1/2          up     standby   down             8             -        100

-------------------------------------------------------------------------------

Port-id        Role      Exp   Def   Dist  Col   Syn   Aggr  Timeout

Activity

-------------------------------------------------------------------------------

1/1/1          actor     No    No    Yes   Yes   Yes   Yes   Yes      Yes

1/1/1          partner   No    No    Yes   Yes   Yes   Yes   Yes      Yes

1/1/2          actor     No    No    No    No    No    Yes   Yes      Yes

1/1/2          partner   No    No    No    No    Yes   Yes   Yes      Yes

===============================================================================

*A:pc5#

LAG Details without MC-LAG Output — 

The following example displays LAG output without 

MC LAG:

*A:pc5# show lag 2 detail

===============================================================================

LAG Details

===============================================================================

Description:

-------------------------------------------------------------------------------

Details

-------------------------------------------------------------------------------

Lag-id              : 2                     Mode                 : access

Adm                 : up                    Opr                  : up

Thres. Exceeded Cnt : 4                     Port Threshold       : 0

Thres. Last Cleared : 04/11/2007 02:03:49   Threshold Action     : down

Dynamic Cost        : false                 Encap Type           : dot1q

Configured Address  : 8e:8b:ff:00:01:42     Lag-IfIndex          :

1342177282

Hardware Address    : 8e:8b:ff:00:01:42     Adapt Qos            :

distribute

Hold-time Down      : 0.0 sec

LACP                : enabled               Mode                 : active

LACP Transmit Intvl : fast                  LACP xmit stdby      : enabled

Selection Criteria  : highest-count         Slave-to-partner     : disabled

Number of sub-groups: 2                     Forced               : -

System Id           : 8e:8b:ff:00:00:00     System Priority      : 32768

Admin Key           : 32768                 Oper Key             : 32768

Prtr System Id      : 8e:89:ff:00:00:00     Prtr System Priority : 32768

Prtr Oper Key       : 32768

-------------------------------------------------------------------------------

Port-id        Adm    Act/Stdby Opr    Primary   Sub-group     Forced

Prio

-------------------------------------------------------------------------------

1/1/1          up     active    up     yes       7             -        99

1/1/2          up     standby   down             8             -        100

-------------------------------------------------------------------------------

Port-id        Role      Exp   Def   Dist  Col   Syn   Aggr  Timeout

Activity

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов