Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 198 | Manualshive

Страница: 198 / 444

background image

Configuration Commands

Page 198

7750 SR OS Interface Configuration Guide

The scheduler policy defined on the ingress context of an HSMDA cannot be changed when local
scheduler overrides exist. The scheduler overrides must be removed prior to changing the scheduler
policy. Once the scheduler policy is changed, any required overrides may be redefined.

The

no

form of the command restores default HSMDA scheduler policy control over the ingress

scheduler on the HSMDA. The

no scheduler-policy

command cannot be executed when scheduler

overrides exist on the ingress HSMDA. The overrides must be removed prior to executing the no
scheduler-policy command.

Parameters

hsmda-scheduler-policy-name —

Specifies an existing policy created in the

config>qos>hsmda-

scheduler-policy

context. The “default” policy name cannot be specified. Instead, the

no

scheduler-policy

command should be executed resulting in the default scheduler policy being

used by the ingress MDA.

sync-e

Syntax

[

no

]

sync-e

Context

config>card>mda

Description

This command enables synchronous Ethernet on the MDA. Then any port on the MDA can be used
as a source port in the sync-if-timing table.

The

no

form of the command disables synchronous Ethernet on the MDA.

«
...
196
197
198
199
200
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

ROADRECORDER 8000

Бренд: Safety Vision Страницы: 40

Firebox SOHO 6 Wireless

Бренд: Watchguard Страницы: 8

Бренд: Usr Страницы: 2

totalstorage 200

Бренд: IBM Страницы: 152

Бренд: NA Страницы: 22

Бренд: Watchguard Страницы: 30

Бренд: Hamlet Страницы: 122

Бренд: Accton Technology Страницы: 78

PXI PXITM -1000

Бренд: National Instruments Страницы: 55

Бренд: Thecus Страницы: 148

Бренд: Quamtum Страницы: 42

Бренд: Crestron Страницы: 40

Бренд: Crestron Страницы: 44

Бренд: Haier Страницы: 9

WP-N6516-M2-16P

Бренд: Wisstar Страницы: 195

Бренд: CYP Страницы: 16

Бренд: AvaLAN Страницы: 13

Бренд: Bolide Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды