Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 240 | Manualshive

Страница: 240 / 444

background image

Configuration Commands

Page 240

7750 SR OS Interface Configuration Guide

Network Port Commands

network

Syntax

network

Context

config>port>ethernet
config>port>sonet-sdh>path
config>port>tdm>ds1

config>port>tdm>ds3
config>port>tdm>e1
config>port>tdm>e3

Description

This command enables access to the context to configure network port parameters.

accounting-policy

Syntax

accounting-policy

policy-id

no accounting-policy

Context

config>port>ethernet>network
config>port>sonet-sdh>path>network
config>port>tdm>ds1>network
config>port>tdm>ds3>network
config>port>tdm>e1>network
config>port>tdm>e3>network

Description

This command configures an accounting policy that can apply to an interface.

An accounting policy must be configured before it can be associated to an interface. If the accounting

policy-id

does not exist, an error is returned.

Accounting policies associated with service billing can only be applied to SAPs. Accounting policies
associated with network ports can only be associated with interfaces.

Only one accounting policy can be associated with an interface at a time.

By default, no specific accounting policy is associated with the interface. If configured, the
accounting policy configured as the default is used.

The

no

form of this command removes the accounting policy association from the network interface,

and the acccounting policy reverts to the default.

policy-id —

The accounting

policy-id

of an existing policy. Accounting policies record either service

(access) or network information. A network accounting policy can only be associated with the
network port configurations. Accounting policies are configured in the config>log>accounting-
policy context.

«
...
238
239
240
241
242
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

Бренд: H3C Страницы: 6

OfficeConnect 3CP4144

Бренд: 3Com Страницы: 4

OfficeConnect 3CP4144

Бренд: 3Com Страницы: 2

Бренд: H3C Страницы: 60

Бренд: H3C Страницы: 149

Бренд: 3Com Страницы: 27

OfficeConnect 3C19500

Бренд: 3Com Страницы: 52

Бренд: F5 Страницы: 72

Бренд: Black Box Страницы: 9

Бренд: Matrix Switch Corporation Страницы: 61

Бренд: Net to Net Technologies Страницы: 4

Бренд: Patton electronics Страницы: 12

Бренд: Juniper Страницы: 825

Бренд: ProCurve Страницы: 2

Бренд: MA lighting Страницы: 49

Бренд: PairGain Страницы: 80

Бренд: RTS Страницы: 3

Fast EtherLink XL PCI 10/100BASE-TXNetwork Interface...

Бренд: 3Com Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды