Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 286 | Manualshive

Страница: 286 / 444

Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 286

Configuration Commands

Page 286

7750 SR OS Interface Configuration Guide

Default

all-ones

Parameters

all-ones —

Defines the 8 bit value to be transmitted as 11111111.

pattern —

Transmits a user-defined pattern.

insert-single-bit-error

Syntax

insert-single-bit-error

Context

config>port>tdm>ds1
config>port>tdm>e1

Description

This command inserts a single bit error for the BERT test.

Default

no bit-error-insertion

invert-data

Syntax

[

no

]

invert-data

Context

config>port>tdm>ds1
config>port>tdm>e1

Description

This command causes all data bits to be inverted, to guarantee ones density. Typically used with AMI
line encoding.

Default

no invert-data

loopback

Syntax

loopback

{

line

|

internal

|

fdl-ansi

|

fdl-bellcore

|

payload-ansi

|

inband-ansi

|

inband-

bellcore

}

no loopback

Context

config>port>tdm>ds1
config>port>tdm>e1

Description

This command puts the specified port or channel into a loopback mode.

The corresponding port or channel must be in a shutdown state in order for the loopback mode to be
enabled. The upper level port or channel or parallel channels should not be affected by the loopback
mode.

NOTE

: This command is not saved in the router configuration between boots.

The

no

form of this command disables the specified type of loopback.

Default

no loopback

«
...
284
285
286
287
288
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов