Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 206 | Manualshive

Страница: 206 / 444

background image

Configuration Commands

Page 206

7750 SR OS Interface Configuration Guide

A value of 100 (the default value) is equivalent to executing the no ing-percentage-of-rate command
and restores the ingress active rate to the normal value.

Parameters

rate-percentage —

The rate-percentage parameter is required and defines the percentage value used

to modify the current ingress active bandwidth of the port. This does not actually change the
bandwidth available on the port in any way. The defined rate-percentage is multiplied by the
ingress active bandwidth of the port. A value of 150 results in an increase of 50% (1.5 x Rate).

Values

1 to 1000

Default

100 (no change to active rate)

The

no

ing-percentage-of-rate command is used to remove any artificial increase or decrease of the

ingress active bandwidth used for ingress buffer space allocation to the port. The no ing-percentage-
of-rate command sets rate-percentage to 100%.

egr-percentage-of-rate

Syntax

egr-percentage-of-rate

rate-percentage

no egr-percentage-of-rate

Context

config>port>modify-buffer-allocation-rate

Description

The egr-percentage-of-rate command is used to increase or decrease the active bandwidth associated
with the egress port that affects the amount of egress buffer space managed by the port. Changing a
ports active bandwidth using the egr-percentage-of-rate command is an effective means of artificially
lowering the buffers managed by one egress port and giving them to other egress ports on the same
MDA.

The egr-percentage-of-rate command accepts a percentage value that increases or decreases the
active bandwidth based on the defined percentage. A value of 50% causes the active bandwidth to be
reduced by 50%. A value of 150% causes the active bandwidth to be increased by 50%. Values from
1 to 1000 percent are supported.

A value of 100 (the default value) is equivalent to executing the no egr-percentage-of-rate command
and restores the egress active rate to the normal value.

Parameters

rate-percentage —

The rate-percentage parameter is required and defines the percentage value used

to modify the current egress active bandwidth of the port. This does not actually change the
bandwidth available on the port in any way. The defined rate-percentage is multiplied by the
egress active bandwidth of the port. A value of 150 results in an increase of 50% (1.5 x Rate).

Values

1 to 1000

Default

100 (no change to active rate)

The

no

egr-percentage-of-rate command is used to remove any artificial increase or decrease of the

egress active bandwidth used for egress buffer space allocation to the port. The no egr-percentage-of-
rate command sets rate-percentage to 100%.

«
...
204
205
206
207
208
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

Бренд: Mafell Страницы: 162

UniFi Cloud Key

Бренд: Ubiquiti Страницы: 13

SteelCentral AppResponse 2180

Бренд: Riverbed Страницы: 82

Бренд: VCS Страницы: 118

Бренд: Observint Страницы: 117

ENHANCED PSD 239 H2R

Бренд: ADTRAN Страницы: 2

Бренд: Supero Страницы: 54

Бренд: Atlantis Land Страницы: 2

Бренд: NetComm Wireless Страницы: 154

Бренд: Allied Telesis Страницы: 2

Бренд: RSupport Страницы: 5

Бренд: bintec elmeg Страницы: 32

Бренд: Niveo Professional Страницы: 49

Бренд: Moeller Страницы: 4

Бренд: DeWalt Страницы: 7

Бренд: DeWalt Страницы: 3

Бренд: MikroTik Страницы: 25

Бренд: Spirent Страницы: 86

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды