manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса, Страница: 360 / 444

Поделиться
Скачать
Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 360

Show Commands

Page 360

7750 SR OS Interface Configuration Guide

Ethernet-Like Medium Statistics Output Fields

Ethernet-like Medium Statistics Output — 

The following table describes Ethernet-like 

medium statistics output fields. 

Sample Output

A:ALA-48# show port 1/3/1 detail

===============================================================================

...

===============================================================================

Ethernet-like Medium Statistics

===============================================================================

Alignment Errors :                   0  Sngl Collisions  :                   0

FCS Errors       :                   0  Mult Collisions  :                   0

Label

Description 

Alignment Errors

The total number of packets received that had a length (excluding 
framing bits, but including FCS octets) of between 64 and 1518 octets, 
inclusive, but had either a bad Frame Check Sequence (FCS) with an 
integral number of octets (FCS Error) or a bad FCS with a non-integral 
number of octets.

FCS Errors

The number of frames received on a particular interface that are an 
integral number of octets in length but do not pass the FCS check. 

SQE Errors

The number of times that the SQE TEST ERROR is received on a par-
ticular interface. 

CSE

The number of times that the carrier sense condition was lost or never 
asserted when attempting to transmit a frame on a particular interface.

Too long Frames

The number of frames received on a particular interface that exceed the 
maximum permitted frame size.

Symbol Errors

For an interface operating at 100 Mb/s, the number of times there was 
an invalid data symbol when a valid carrier was present.

Sngl Collisions

The number of frames that are involved in a single collision, and are 
subsequently transmitted successfully. 

Mult Collisions

The number of frames that are involved in more than one collision and 
are subsequently transmitted successfully.

Late Collisions

The number of times that a collision is detected on a particular inter-
face later than one slotTime into the transmission of a packet.

Excess Collisns

The number of frames for which transmission on a particular interface 
fails due to excessive collisions.

Int MAC Tx Errs

The number of frames for which transmission on a particular interface 
fails due to an internal MAC sublayer transmit error,

Int MAC Rx Errs

The number of frames for which reception on a particular interface 
fails due to an internal MAC sublayer receive error.

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов