manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса, Страница: 276 / 444

Поделиться
Скачать
Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 276

Configuration Commands

Page 276

7750 SR OS Interface Configuration Guide

e3

Syntax

e3 

sonet-sdh-index

Context

config>port>tdm

Description

This command enables the context to configure E-3 parameters. E-3 lines provide a speed of 44.736 
Mbps and is also frequently used by service providers. E-3 lines carry 16 E-1 signals with a data rate 
of 34.368 Mbps. 

A E-3 connection typically supports data rates of about 43 Mbps. A E-3 line actually consists of 672 
individual channels, each supporting 64 Kbps. E-3 lines are used mainly by Service Providers to 
connect to the Internet backbone and for the backbone itself. 

Depending on the MDA type, the E-3 parameters must be disabled if clear channel is enabled by 
default (for example, on the m12-ds3e3 MDA). Clear channel is a channel that uses out-of-band 
signaling, not in-band signaling, so the channel's entire bit rate is available. Channelization must be 
explicitly specified. Note that if E-3 nodes are provisioned on the channelized SONET/SDH MDA 
you must provision the parent STS-1 SONET/STM0 SDH path first.

North America uses the T-Carrier system while Europe uses the E-Carrier system of transmission, 
using multiples of the DS system. Digital signals are carried inside the carrier systems. 

The 

no

 form of this command disables E-3 capabilities.

bert 

Syntax

bert 

{

2e3

|

2e9

|

2e11

|

2e15

|

2e20

|

2e20q

|

2e23

|

ones

|

zeros

|

alternating

} 

duration 

duration

no bert

Context

config>port>tdm>ds1
config>port>tdm>ds3
config>port>tdm>e1
config>port>tdm>e3

Description

This command initiates or restarts a Bit Error Rate Test (BERT) on the associated DS-1/E-1 or DS-3/
E-3 circuit.

The associated DS-1, E-1, DS-3, or E-3 must be in a shutdown (admin down) state to initiate this test.

The 

no

 form of the command terminates the BERT test if it has not yet completed.

Notes: 

• This command is not saved in the router configuration between boots.

• The 4-port OC-3/STM-1 and the 1-port OC-12/STM-4 ASAP MDA supports up to 28 concur-

rent BERT tests per MDA. The 4-port and 12-port DS-3/E-3 ASAP MDAs support a single 
BERT test per MDA. An attempt to configure more BERT tests can result in an error indicating 
an operation failure due to resource exhaustion. 

• If the ASAP MDA BERT error insertion 

rate

 command is executed when tests are running, it 

will not take effect until test is restarted. 

Default

2e3

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов