manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса, Страница: 255 / 444

Поделиться
Скачать
Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 255

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 255

report-alarm

Syntax

[

no

]

 report-alarm

 [

loc

] [

lais

]

 

[

lrdi

]

 

[

ss1f

] [

lb2er-sd

]

 

[

lb2er-sf

]

 

[

slof

]

 

[

slos

]

 

[

lrei

]

Context

config>port>sonet-sdh

Description

This command enables logging of SONET (SDH) line and section alarms for a SONET-SDH port. 
Only line and section alarms can be configured in the SONET/SDH context, for path alarms see the 

sonet-sdh

>

path

 context.

The 

no

 form of this command disables logging of the specified alarms

Parameters

loc — 

Reports a loss of clock which causes the operational state of the port to be shut down.

Default

loc

 alarms are issued.

lais — 

Reports line alarm indication signal errors. When configured, 

lais

 alarms are raised and 

cleared. 

Default

lais

 alarms are not issued.

lrdi — 

Reports line remote defect indication errors. LRDI's are caused by remote LOF, LOC, LOS. 

When configured, 

lrdi

 alarms are raised and cleared. 

Default

lrdi

 alarms are issued.

ss1f — 

Reports section synchronization failure which is detected when the S1 byte is not consistent 

for 8 consecutive frames. When configured, 

ss1f

 alarms are raised and cleared. 

Default

ss1f

 alarms are not issued.

lb2er-sd — 

Reports line signal degradation BER (bit interleaved parity) errors. Use the threshold 

command to set the error rate(s) that when crossed determine signal degradation and signal 
failure. When configured, 

lb2er-sd

 alarms are raised and cleared.

Default

lb2er-sd

 alarms are not issued. 

lb2er-sf — 

Reports line signal failure BER errors. Use the threshold command to set the error rate(s) 

that when crossed determine signal degradation and signal failure.When configured, 

lb2er-sf

 

alarms are raised and cleared. 

Default

lb2er-sf

 alarms are issued.

slof — 

Reports section loss of frame errors. When configured, 

slof

 alarms are raised and cleared.

Default

slof

 alarms are issued.

slos — 

Reports a section loss of signal error on the transmit side. When configured, 

slos

 alarms are 

raised and cleared. 

Default

slos

 alarms are issued.

lrei — 

Reports a line error condition raised by the remote as a result of b1 errors received from this 

node. When configured, 

lrei

 traps are raised but not cleared

Default

lrei

 traps are not issued.

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов