Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 368 | Manualshive

Страница: 368 / 444

background image

Show Commands

Page 368

7750 SR OS Interface Configuration Guide

A;ALA-1#

Port Frame Relay Output Fields

Port Frame Relay Output —

The following table describes port Frame Relay output fields.

Sample Output

A:ALA-49>config>port# show port 8/1/2 frame-relay

===============================================================================

Frame Relay Info for 8/1/2

===============================================================================

Mode : dte LMI Type : itu

FR Interface Status : fault

N391 DTE : 6 N392 DCE : 3

N392 DTE : 3 N393 DCE : 4

N393 DTE : 4 T392 DCE : 15

T391 DTE : 10

Tx Status Enquiry : 0 Rx Status Enquiry : 0

Rx Status Messages : 0 Tx Status Messages : 0

Status Message Timeouts : 0 Status Enquiry Timeouts : 0

Discarded Messages : 0 Inv. RxSeqNum Messages : 0

===============================================================================

A:ALA-49>config>port#

port

PPP Output Fields

Port PPP Output —

The following table describes port PPP output fields.

Label

Description

Mode

Displays the mode of the interface. It can be set as Data terminal equip-
ment (dte) or Data circuit-terminating equipment (DCE).

LMI Type

Displays the LMI type.

FR Interface

Status

Displays the status of the Frame Relay interface as determined by the
performance of the dlcmi. If no DLCMI is running, the Frame Relay
interface will stay in the running state indefinitely.

Label

Description

Protocol

Displays the applicable protocols for the specified port.

State

Displays the current status of a PPP link. Values include initial, start-
ing, closed, stopped, closing, stopping, requestSent, ackReceived, ack-
Sent, opened.

Last Change

Displays the last time the PPP link state changed.

Restart Count

Displays the number of times that this Control Protocol has reached the
'open' state.

Last Cleared

Displays the date and time the restart count was set to zero.

Local IP address

Displays the IP address assigned the local end of the PPP link.

«
...
366
367
368
369
370
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

Бренд: 4RF Страницы: 7

Бренд: C&H Technologies Страницы: 46

Бренд: CAME Страницы: 19

Бренд: Vonets Страницы: 8

Nighthawk M6 Pro

Бренд: AT&T Страницы: 2

Бренд: Google Страницы: 14

Бренд: Eicon Networks Страницы: 32

RS-232/422/485 Serial Card CE 3PXCC4A

Бренд: B&B Electronics Страницы: 47

Бренд: Z Microsystems Страницы: 51

Бренд: Idis Страницы: 85

DataPlot CB1224

Бренд: B-G Instruments Страницы: 4

Бренд: H3C Страницы: 4

DVI-Vision-IP-Fiber

Бренд: G&D Страницы: 240

Бренд: Tenda Страницы: 120

NVR2104/2108HS-W-4KS2 1U

Бренд: Dahua Technology Страницы: 363

RuggedSwitch RS500

Бренд: RuggedCom Страницы: 16

Бренд: Aztech Страницы: 13

VDA-NVR2108W4KS2

Бренд: Dahua Technology Страницы: 363

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды