Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 224 | Manualshive

Страница: 224 / 444

Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 224

Configuration Commands

Page 224

7750 SR OS Interface Configuration Guide

dot1q-etype

Syntax

dot1q-etype

0x0600..0xffff

no dot1q-etype

Context

config>port>ethernet

Description

This command specifies the Ethertype expected when the port's encapsualtion type is dot1q. Dot1q
encapsulation is supported only on Ethernet interfaces.

The

no

form of this command reverts the dot1q-etype value to the default.

Parameters

0x0600..0xffff —

Specifies the Ethertype to expect.

Default

If the encap-type is dot1p, then the default is 0x8100.
If the encap-type is qinq, then the default is 0x8100.

duplex

Syntax

duplex

{

full

|

half

}

Context

config>port>ethernet

Description

This command configures the duplex of a Fast Ethernet port when autonegotiation is disabled.

This configuration command allows for the configuration of the duplex mode of a Fast Ethernet port.
If the port is configured to autonegotiate this parameter is ignored.

Default

full

Parameters

full —

Sets the link to full duplex mode.

half —

Sets the link to half duplex mode.

efm-oam

Syntax

efm-oam

Context

config>port>ethernet

Description

This command configures EFM-OAM attributes.

accept-remote-loopback

Syntax

[

no

]

accept-remote-loopback

Context

config>port>ethernet>efm-oam

Description

This command enables reactions to loopback control OAM PDUs from peers.

«
...
222
223
224
225
226
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов