Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 87 | Manualshive

Страница: 87 / 444

background image

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 87

802.1x Timers

The 802.1x authentication procedure is controlled by a number of configurable timers and scalars.
There are two separate sets, one for the EAPOL message exchange and one for the RADIUS
message exchange. See

for an example of the timers.

EAPOL timers:

•

transit-period

— Indicates how many seconds the Authenticator will listen for an

EAP-Response/ID frame. If the timer expires, a new EAP-Request/ID frame will be sent
and the timer restarted. The default value is 60. The range is 1-3600 seconds.

•

supplicant-timeout

— This timer is started at the beginning of a new authentication

procedure (transmission of first EAP-Request/ID frame). If the timer expires before an
EAP-Response/ID frame is received, the 802.1x authentication session is considered as
having failed. The default value is 30. The range is 1-300.

•

quiet-period

— Indicates number of seconds between authentication sessions It is

started after logoff, after sending an EAP-Failure message or after expiry of the
supplicant-timeout timer. The default value is 60. The range is 1-3600.

RADIUS timer and scaler:

•

max-auth-req

— Indicates the maximum number of times that the 7750 SR will send an

authentication request to the RADIUS server before the procedure is considered as having
failed. The default value is value 2. The range is 1-10.

•

server-timeout

— Indicates how many seconds the authenticator will wait for a

RADIUS response message. If the timer expires, the access request message is sent again,
up to

max-auth-req

times. The default value is 60. The range is 1-3600 seconds.

«
...
85
86
87
88
89
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

Бренд: Campbell Страницы: 42

Бренд: Paradyne Страницы: 2

Бренд: bintec elmeg Страницы: 33

Бренд: Qixiang Technology Страницы: 16

Proventia A1204

Бренд: Internet Security Systems Страницы: 42

Бренд: TP-Link Страницы: 2

Бренд: ICP DAS USA Страницы: 8

Бренд: ZyXEL Communications Страницы: 422

Бренд: Ozenda Страницы: 116

Бренд: Digisol Страницы: 22

NVR41-4KS2 Series

Бренд: Dahua Страницы: 452

Бренд: Active Communications Страницы: 10

Бренд: Tripp Lite Страницы: 3

ipRocketLink 3101 Series

Бренд: Patton Страницы: 119

Бренд: IBM Страницы: 168

Бренд: Clas Ohlson Страницы: 4

Бренд: Valcom Страницы: 4

Бренд: ZyXEL Communications Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды