manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса, Страница: 269 / 444

Поделиться
Скачать
Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 269

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 269

Frame Relay Commands

frame-relay

Syntax

frame-relay

Context

config>port>sonet-sdh>path
config>port>tdm>ds1>channel-group
config>port>tdm>ds3
config>port>tdm>e1>channel-group
config>port>tdm>e3

Description

This command allows access to the context to configure the Frame Relay Local Management 
Interface (LMI) operational parameters for a SONET/SDH PoS link, a DS-0 channel group, or a DS-
3/E-3 port or channel.

The port’s 

mode

 must be set to 

access

 in 

config>port>sonet-sdh>path>mode access

 context. 

The port’s encapsulation type must be set to 

frame-relay

 in the 

config>port>sonet-

sdh>path>encap-type frame-relay 

context.

The 

no

 form of this command removes the Frame Relay LMI operational parameters.

lmi-type

Syntax

lmi-type 

{

ansi

 | 

itu

 | 

none

 | 

rev1

}

no lmi-type

Context

config>port>sonet-sdh>path>frame-relay
config>port>tdm>ds1>channel-group>frame-relay
config>port>tdm>ds3>frame-relay
config>port>tdm>e1>channel-group>frame-relay
config>port>tdm>e3>frame-relay

Description

This command configures the Local Management Interface (LMI) type for Frame Relay interfaces. 
LMIs are sets of enhancements to the basic Frame Relay specification.

The 

no

 form of this command changes the LMI type back to the default value.

Default

itu

Parameters

ansi  — 

Use ANSI T1.617 Annex D.

itu  — 

Use ITU-T Q933 Annex A.

none  — 

Disable Frame Relay LMI on the given port/channel.

rev1  — 

Use the Rev 1 version of ANSI T1.617 Annex D.

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов