manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса, Страница: 232 / 444

Поделиться
Скачать
Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 232

Configuration Commands

Page 232

7750 SR OS Interface Configuration Guide

•

include-l4

 — Enables inherits system-wide settings including Layer 4 source and destination 

port value in hashing algorithm.

•

exclude-l4

 — Layer 4 source and destination port value will not be included in hashing.

•

no load-balancing-algorithm

 — Inherits system-wide settings.

The hashing algorithm addresses finer spraying granularity where many hosts are connected to the 
network. To address more efficient traffic distribution between network links (forming a LAG 
group), a hashing algorithm extension takes into account L4 information (i.e., src/dst L4-protocol 
port).
The hashing index can be calculated according to the following algorithm:

If [(TCP or UDP traffic) & enabled] 

    

hash (<TCP/UDP ports>, <IP addresses>) 

else if (IP traffic) 

    

hash (<IP addresses>) 

else 

    

hash (<MAC addresses>)

endif

This algorithm will be used in all cases where IP information in per-packet hashing is included (see 

LAG and ECMP Hashing on page 72

) except in the following cases: 

• Fragmented packets 

• Packets received from a VPRN tunnel.

Use of Layer 4 information (TCP/UDP ports) will not be used in following cases:

• Fragmented packets.

• Packets received from a VPRN tunnel.

Default

no load-balancing-algorithm

Parameters

option — 

Specifies the load balancing algorithm to be used on this port.

Values

include-l4 

— Specifies that the source and destination ports are used in the hashing 

algorithm.

exclude-l4

 — Specifies that the source and destination ports are not used in the 

hashing algorithm.

pbb-etype

Syntax

pbb-etype

 [

0x0600

..

0xffff

] 

no pbb-etype

Context

config>port>ethernet

Default

0x88E7

Description

This command configures the Ethertype used for PBB encapsulation.

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов