Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 270 | Manualshive

Страница: 270 / 444

background image

Configuration Commands

Page 270

7750 SR OS Interface Configuration Guide

mode

Syntax

mode

{

dce

|

dte | bidir

}

Context

config>port>sonet-sdh>path>frame-relay
config>port>tdm>ds1>channel-group>frame-relay
config>port>tdm>ds3>frame-relay
config>port>tdm>e1>channel-group>frame-relay
config>port>tdm>e3>frame-relay

Description

This command sets the Frame Relay interface into the DCE, DTE, or Bidirectional mode of LMI
operation. The DTE mode causes the router to send status enquiries over the interface. The DCE
mode causes the router to respond to status enquiries. In bidirectional mode, the router performs both
DTE and DCE operation over the FR interface. The bidirectional mode applies to the ANSI and ITU
LMI types only.

This feature is used when two routers are connected back-to-back, running frame relay encapsulation.

Default

dte

Parameters

dce —

Enables the DCE mode.

dte —

Enables the DTE mode.

bidir

—

Enables the bidirectional mode for LMI types ANSI and ITU.

n391dte

Syntax

n391dte

intervals

no n391dte

Context

config>port>sonet-sdh>path>frame-relay
config>port>tdm>ds1>channel-group>frame-relay
config>port>tdm>ds3>frame-relay
config>port>tdm>e1>channel-group>frame-relay
config>port>tdm>e3>frame-relay

Description

This command sets the DTE full status polling interval for the Frame Relay Local Management
Interface (LMI). The number specifies the frequency at which inquiries expect a full status report.

The

no

form of this command returns the

n391dte

counter to the default value.

Default

6

Parameters

intervals —

The number of exchanges to be done before requesting a full-status report. A value of 1

specifies to receive full-status messages only.

Values

1 — 255

«
...
268
269
270
271
272
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

UR5i v2 Libratum

Бренд: B+B SmartWorx Страницы: 8

Бренд: B+B SmartWorx Страницы: 8

Бренд: Amperes Страницы: 8

Бренд: Stephen Страницы: 102

BladeCenter Management Module

Бренд: IBM Страницы: 184

EonServ 5000 Series

Бренд: Surveon Страницы: 33

SmartMesh IA-510 D2511

Бренд: Dust Networks Страницы: 30

Бренд: Draytek Страницы: 2

Бренд: Genie Страницы: 6

Network Adapter AC AAP

Бренд: Extron electronics Страницы: 2

CNGE28FX4TX24MS2

Бренд: Comnet Страницы: 154

Бренд: Thecus Страницы: 148

I-FLY A02-WRA4-54G

Бренд: Atlantis Land Страницы: 3

Router 3000 Series

Бренд: 3Com Страницы: 37

FrameSaver DSL 9783 CSU/DSU

Бренд: Paradyne Страницы: 233

Бренд: Adeunis RF Страницы: 68

Бренд: Crestron Страницы: 2

Zum ZUMMESH-NETBRIDGE

Бренд: Crestron Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды