Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 130 | Manualshive

Страница: 130 / 444

background image

Configuring Ports

Page 130

7750 SR OS Interface Configuration Guide

Configuring a Channelized Any Service Any Port (ASAP) OC3-SFP Port

This section provides examples to configure PPP, FR, cHDLC, and ATM n*DS0 channels on a
channelized port on channelized ASAP OC-3 SFP MDA in slot 1/1/1. The ASAP OC-12 SFP
MDAalso supports the SONET options.

ALA-A>config# port 1/1/1

At this level you must choose the tributary. When provisioning DS3 nodes on a channelized ASAP
OC-3 MDA, you must provision the parent STS1-1 SONET path first.

A:ALA-A>config>port# sonet-sdh

A:ALA-A>config>port>sonet-sdh# framing sdh

A:ALA-A>config>port>sonet-sdh# path sts1-1

A:ALA-A>config>port>sonet-sdh>path# no shutdown

A:ALA-A>config>port>sonet-sdh>path# exit

A:ALA-A>config>port>sonet-sdh# info

----------------------------------------------

sonet-sdh

framing sdh

path sts1-1

no shutdown

exit

exit

----------------------------------------------

A:ALA-A>config>port>sonet-sdh#

In order to set the channelized mode on a port, the DS3 parameter must be in a shut down state.
Clear channel uses out-of-band signaling, not in-band signaling, so the channel's entire bit rate is
available. Channelized ports use in-band signalling and must be explicitly enabled.

A:ALA-A>config>port# tdm

A:ALA-A>config>port>tdm# ds3 1

A:ALA-A>config>port>tdm>ds3# shutdown

A:ALA-A>config>port>tdm>ds3# channelized e1

A:ALA-A>config>port>tdm>ds3# no shutdown

A:ALA-A>config>port>tdm>ds3# exit

A:ALA-A>config>port# info

----------------------------------------------

sonet-sdh

path sts1-1

no shutdown

exit

exit

tdm

ds3 1

channelized e1

no shutdown

exit

exit

no shutdown

«
...
128
129
130
131
132
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

Бренд: H3C Страницы: 22

Бренд: H3C Страницы: 3

Бренд: National Instruments Страницы: 36

Transportation FiberinMotion

Бренд: Radwin Страницы: 122

Бренд: XAVI Technologies Corp. Страницы: 71

Бренд: E-TOP Страницы: 76

Бренд: WaiLan Страницы: 27

ION 1200 Series

Бренд: PaloAlto Networks Страницы: 90

Бренд: Radicom Страницы: 27

RabbitCore RCM4400W

Бренд: Rabbit Страницы: 126

ControlPoint 2000

Бренд: 4Home Страницы: 20

Бренд: NETGEAR Страницы: 2

Бренд: Perle Страницы: 2

Бренд: ProCurve Страницы: 2

Бренд: AirTies Страницы: 28

Бренд: NetCommWireless Страницы: 28

X-Pedition XSR-1850

Бренд: Enterasys Страницы: 114

Odin CL-4 Connect

Бренд: DAPAudio Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды