Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 282 | Manualshive

Страница: 282 / 444

background image

Configuration Commands

Page 282

7750 SR OS Interface Configuration Guide

• Out of Cell Delineation (OCD) event count. The OCD event count is described in RFC 2515,

Definitions of Managed Objects for ATM Management

. Note that multiple events occurring

within a second will be counted as 1 event for ASAP MDAs as a result of a hardware limit.

• Loss of Cell Delineation defect/alarm. The LCD defect/alarm is defined in RFC 2515,

Defini-

tions of Managed Objects for ATM Management

. When a path is in an LCD defect state, the

path’s operational status will be down. When a path exits the LCD state, the path’s operational
status will change to up (assuming nothing else causes the path to stay down). A trap is raised to
indicate the LCD status change. Also, a P-RDI is sent to indicate the defect to the remote end.

The

no

form of this command restores the default.

Default

bcp-null

atm —

Specifies the encapsulation on the port is ATM.

bcp-null —

When selected, this keyword specifies that only a single service is configured on this

channel and IEEE 802.1Q tags are not used as a service delimiter. Any IEEE 802.1Q tags
encountered are regarded as part of the customer payload and transparently forwarded. When
bcp-null encapsulation is specified, the PPP Bridge Control Protocol (BCP) is activated and all
packets on this access port will be encapsulated in accordance with the BCP protocol.

bcp-dot1q —

When selected, this keyword specifies that ingress frames carry IEEE 802.1Q tags and

the tags are used as service delimiter. Any untagged packets are silently discarded with
exception of protocol specific packets. When bcp-dot1q encapsulation is specified, the PPP
Bridge Control Protocol (BCP) is activated and all packets on this access port will be
encapsulated in accordance with the BCP protocol.

ipcp —

Ingress frames are encapsulated according to the IP Control Protocol. When ipcp

encapsulation is specified, the PPP IP Control Protocol will be activated and only packets that
comply with IPCP encapsulation are processed; others are silently discarded.

ppp-auto —

(Network mode) Enables PPP on the associated port/channel. The activation of ipcp

and mplscp is automatically enabled depending on the protocol configuration. This encap type is
only valid on ports/channels in network mode.

frame-relay —

Enables frame relay on the associated port/channel.

wan-mirror —

The port is used for mirroring of frame-relay and POS ports. On these ports, no link

management protocol will run.

cisco-hdlc —

Monitors line status on a serial interface by exchanging keepalive request messages

with peer network devices.

cem —

On circuit emulation CMAs and MDAs, only the

cem

encap-type is supported. All other

values are blocked with an appropriate warning. The

cem

encap-type is not supported on other

CMAs and MDAs and are blocked with an appropriate warning.

«
...
280
281
282
283
284
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

Бренд: Wave wifi Страницы: 2

Бренд: JCG Страницы: 2

Бренд: Edge-Core Страницы: 7

LinkSmart KW6515

Бренд: Kasda Страницы: 31

Бренд: Toto Link Страницы: 55

DSL5068EN(1T1R)

Бренд: Aztech Страницы: 40

RealPort Ethernet 10/100

Бренд: Xircom Страницы: 30

Бренд: Tektronix Страницы: 178

ConnectX-3 Pro MCX349A-XCCN

Бренд: Mellanox Technologies Страницы: 35

Бренд: Waver Страницы: 36

Бренд: netsys Страницы: 164

Бренд: Spirent Страницы: 22

Бренд: Hi-flying Страницы: 59

Бренд: Supero Страницы: 54

Бренд: Honeywell Home Страницы: 36

Бренд: CalAmp Страницы: 52

Linktropy MINI-G

Бренд: Apposite Technologies Страницы: 57

Бренд: QNAP Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды