manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса, Страница: 402 / 444

Поделиться
Скачать
Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 402

Show Commands

Page 402

7750 SR OS Interface Configuration Guide

Sample Output

A:timetra-sim110# show multilink-bundle 

===============================================================================

Bundle Summary

===============================================================================

Bundle               Type    Admin     Oper      Port      Min    Total/       

Id                           State     State     State     Links  Active Links 

-------------------------------------------------------------------------------

bundle-ppp-1/1.1     mlppp   Down      Down      Ghost     1      0/0          

bundle-ima-1/1.2     ima     Down      Down      Link Up   1      1/0          

-------------------------------------------------------------------------------

Bundles : 2

===============================================================================

A:timetra-sim110#

*A:timetra-44-cpm2# show multilink-bundle detail

===============================================================================

Description        : MultiLink Bundle

Bundle Id          : bundle-ppp-1/1.1   Type               : mlppp             

Admin Status       : up                 Oper Status        : down              

Minimum Links      : 1                  Bundle IfIndex     : 572522497         

Total Links        : 3                  Active Links       : 0                 

Red Diff Delay     : 0                  Yellow Diff Delay  : 0                 

Red Diff Delay Act : none               MRRU               : 1524              

Short Sequence     : true               Oper MRRU          : 1524              

Oper MTU           : 1526               Fragment Threshold : 128 bytes         

Fragment Thresh-

old

Displays configured fragment threshold value for this bundle.

Up Time

Displays time elapsed since the last bundle transition to Up when part 
of bundle information. Displays time elapsed since the last link transi-
tion to active when part of member information.

Bandwidth

Displays bandwidth configured for this IMA bundle in Kbytes.

Primary Port 

Member

Displays the portId of the IMA group member chosen as a Primary 
Port.

Member Port Id

Displays portId of each member of this bundle.

Admin

Displays administrative port status of a member link.

Oper

Displays operational port status of a member link.

Active

Displays whether a member link is active or not.

Down Reason

Displays the reason for why a member link is not active.

Traffic and Port 

statistics

The traffic and port statistics information displayed for bundles when 
detail option is selected is the same as information displayed for physi-
cal ports.

Label

Description  (Continued)

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов