Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 383 | Manualshive

Страница: 383 / 444

Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 383

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 383

ATM PVT Detail Output Fields

Output

Port ATM PVT Detail Output —

The following table describes port ATM PVT detail output

fields.

Sample Output

A:SR1_5>config>service# show port 1/2/2 atm pvt 0.0 detail

==============================================================================

ATM PVT

==============================================================================

Port Id : 1/2/2 VPI Range : 0.0

Admin State : up Oper state : up

Owner : SAP

Label

Description

Port Id

The port ID configured or displayed in the

slot/mda/port

format.

VPI/VCI

Displays the VPI/VCI values.

Admin State

Displays the administrative state of the interface connection.

Oper State

Indicates the status of the ATM interface.

Encap Type

Indicates the encapsulation type.

Owner

Identifies the system entity that owns a specific ATM connection.

Endpoint Type

Displays the endpoint type.

Cast Type

Indicates the connection topology type.

Ing. Td Idx

Specifies the ATM traffic descriptor profile that applies to the receive
direction of the interface connection.

Egr. Td Idx

Specifies the ATM traffic descriptor profile that applies to the transmit
direction of the interface connection.

Last Changed

Indicates the date and time when the interface connection entered its
current operational state.

Octets

Displays the number of input and output octets.
HEC discarded cells are not included in the input octet numbers.

Cells

Displays the number of input and output cells.
HEC discarded cells are not included in the input cell numbers.

Dropped CLP

Displays the number of times the CLP1 cells have been dropped. CLP1
cells have lower priority than CLP0 cells and are expected to be dis-
carded first in times of congestion.

Dropped Cells

Displays the number of cells dropped by the ATM SAR device.

Tagged Cells

Displays the number of cells that have been demoted from CLP0 to
CLP1.

«
...
381
382
383
384
385
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов