Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 92 | Manualshive

Страница: 92 / 444

Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 92

Port Features

Page 92

7750 SR OS Interface Configuration Guide

Modifying MTU Defaults

MTU parameters should be modified on the service level as well as the port level.

•

The service-level MTU parameters configure the service payload (Maximum
Transmission Unit – MTU) in bytes for the service ID overriding the service-type default
MTU.

•

The port-level MTU parameters configure the maximum payload MTU size for an
Ethernet port or SONET/SDH SONET path (sub-port)

o

r TDM port/channel, or a channel

that is part of a multilink bundle or LAG.

The default MTU values should be modified to ensure that packets are not dropped due to frame
size limitations. The service MTU must be less than or equal to both the SAP port MTU and the
SDP path MTU values. When an SDP is configured on a network port using default port MTU
values, the operational path MTU can be less than the service MTU. In this case, enter the

show

service sdp

command to check the operational state. If the operational state is down, then

modify the MTU value accordingly.

Configuration Example

In order for the maximum length service frame to successfully travel from a local ingress SAP to a
remote egress SAP, the MTU values configured on the local ingress SAP, the SDP (GRE or
MPLS), and the egress SAP must be coordinated to accept the maximum frame size the service
can forward. For example, the targeted MTU values to configure for a distributed Epipe service
(ALA-A and ALA-B) are displayed in

.

Figure 24: MTU Configuration Example

OSSG012

SAP

1/1/1

encap:

100

Network

2/1/1

SAP

4/1/1

encap:

null

Network

3/1/1

ALA-A

ALA-B

«
...
90
91
92
93
94
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов