manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса, Страница: 364 / 444

Поделиться
Скачать
Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 364

Show Commands

Page 364

7750 SR OS Interface Configuration Guide

Channelized Port Output Fields

Channelized Port Output — 

The following table describes channelized port output fields.

Label

Description 

Description

A text description of the port.

Interface

The port ID displayed in the 

slot/mda/port

 format.

TimeSlots

Specifies the DS0 timeslot used in the T1/E1 channel-group. 

Speed

Indicates the speed of the DS0 channels used in the associated channel-
group.

CRC

Indicates the precision of the cyclic redundancy check. 

16  — 

A16-bit CRC calculation. 

32  — 

A 32-bit CRC calculation. 32-bit CRC increases the error 

detection ability, but it also adds some performance overhead.

Admin Status

Up — 

The port is administratively up.

Down — 

The administratively down.

Oper Status

Up — 

The port is operationally up.

Down — 

The port is operationally down.

Last State Change

Displays the last time the operational status of the port changed state.

Chan-Grp IfIndex

Displays the channel group’s interface index number which reflects its 
initialization sequence.

Configured Mode

network — 

The port is configured for transport network use.

access — 

The port is configured for service access. Channelized 

ports are always access ports.

Encap Type

The type of encapsulation protocol configured on this port's network 
interface. 

bcp-null — 

Indicates that BCP is used as the NCP control protocol.

dot1q — 

Indicates that ingress frames carry 802.1Q tags where each 

tag signifies a different service.

Oper MTU

The negotiated size of the largest packet which can be sent on the chan-
nel, specified in octets. For channels that are used to transmit network 
datagrams, this is the size of the largest network datagram that can be 
sent.

Physical Link

Indicates whether or not the port has a physical link.

U

nicast Packets 

Input/Output

The number of packets, delivered by this sub-layer to a higher (sub-) 
layer, which were not addressed to a multicast or broadcast address at 
this sub-layer.

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов