Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 322

Страница: 322 / 444

Show Commands

Page 322

7750 SR OS Interface Configuration Guide

card

Syntax

card

[

slot-number

]

[

detail

]

card state

Context

show

Description

This command displays card information.

If no command line parameters are specified, a card summary for all cards is displayed.

Parameters

slot-number —

Displays information for the specified card slot.

Default

Displays all cards.

Values

Depending on the chassis model, IOM slots can be numbered from 1 - 10
SF/CPM slots are A, B (upper or lowercase)

state —

Displays provisioned and equipped card and MDA information.

detail —

Displays detailed card information.

Default

Displays summary information only

Output

Show Card Output —

The following table describes show card output fields.

Sample Output

A:ALA-48# show card

===============================================================================

Card Summary

===============================================================================

Slot Provisioned Equipped Admin Operational

Card-type Card-type State State

-------------------------------------------------------------------------------

1 iom-20g iom-20g up up

2 iom-20g iom-20g up up

A sfm-400g sfm-200g up up/standby

B sfm-400g sfm-200g up up/active

Label

Description

Slot

The slot number of the card in the chassis.

Provisioned

Card-type

The card type that is configured for the slot.

Equipped Card-

type

The card type that is actually populated in the slot.

Admin State

Up —

The card is administratively up.

Down —

The card is administratively down.

Operational

State

Up —

The card is operationally up.

Down —

The card is operationally down.

Содержание 7750 SR OS





























































































































































































































































































































































































































































Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса

Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды