Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 236 | Manualshive

Страница: 236 / 444

Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 236

Configuration Commands

Page 236

7750 SR OS Interface Configuration Guide

quiet-period

Syntax

quiet-period

seconds

no quiet-period

Context

config>port>ethernet>dot1x

Description

This command configures the period between two authentication sessions during which no EAPOL
frames are sent by the 7750 SR.

The

no

form of this command returns the value to the default.

Default

30

Parameters

seconds —

Specifies the quiet period in seconds.

Values

1 — 3600

radius-plcy

Syntax

radius-plcy

name

no radius-plcy

Context

config>port>ethernet>dot1x

Description

This command configures the RADIUS policy to be used for 802.1x authentication. An 802.1x
RADIUS policy must be configured (under config>security>dot1x) before it can be associated to a
port. If the RADIUS policy-id does not exist, an error is returned. Only one 802.1x RADIUS policy
can be associated with a port at a time.

The

no

form of this command removes the RADIUS policy association.

Default

no radius-plcy

Parameters

name —

Specifies an existing 802.1x RADIUS policy name.

re-auth-period

Syntax

re-auth-period

seconds

no re-auth-period

Context

config>port>ethernet>dot1x

Description

This command configures the period after which re-authentication is performed. This value is only
relevant if re-authentication is enabled.

The

no

form of this command returns the value to the default.

Default

3600

Parameters

seconds —

The re-authentication delay period in seconds.

«
...
234
235
236
237
238
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов