Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 325

Страница: 325 / 444

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 325

Sample Output

A:ALA-49# show card 3 detail

===============================================================================

Card 3

===============================================================================

Slot Provisioned Equipped Admin Operational

Card-type Card-type State State

-------------------------------------------------------------------------------

3 iom2-20g up provisioned

IOM Card Specific Data

Clock source : none

Available MDA slots : 2

Installed MDAs : 0

Hardware Data

Part number :

CLEI code :

Serial number :

Manufacture date :

Manufacturing string :

Manufacturing deviations :

Administrative state : up

Operational state : provisioned

Software boot version :

Software version :

Time of last boot : N/A

Current alarm state : alarm cleared

Base MAC address : 00:00:00:00:00:00

Memory capacity : 0 MB

===============================================================================

A:ALA-49#

Temperature

threshold

The value above which the internal temperature must rise in order to
indicate that the temperature is critical.

Software boot

version

The version of the boot image.

Software version

The software version number.

Time of last

boot

The date and time the most recent boot occurred.

Current alarm

state

Displays the alarm conditions for the specific board.

Base MAC address

Displays the base MAC address of the hardware component.

Memory Capacity

Displays the memory capacity of the card.

Label

Description (Continued)

Содержание 7750 SR OS





























































































































































































































































































































































































































































Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса

Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды