Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 444

background image

Port Features

Page 64

7750 SR OS Interface Configuration Guide

MC-APS for ATM SAP with ATM VLL and Ethernet VLL Redundancy

By extending the support of MC-APS to ATM VLLs and Ethernet VLL with ATM SAPs allow
MC-APS to operate with pseudowire redundancy in a similar manner that MC-LAG operates with
pseudowire redundancy.

Note that MC-APS for ATM SAP is only supported for VC and VT SAPs. MC-APS is not
supported for VP SAP.

The combination of these features provides a solution for access node redundancy and network
redundancy as shown in

Figure 12: Access and Node and Network Resilience

Fig_3

Aggregation

Node

A

Aggregation

Node

C

Standby

TLDP

Active

Aggregation

Node

B

MSAN

MSAN

Aggregation

Node

D

Standby

Active

Standby

Standby

Active

Standby

Standby

Active

Active

Active

Inter-ChassisPW

for VLL

Inter-ChassisPW

for VLL

Aggregation

Node

A

Aggregation

Node

C

TLDP

Active

Aggregation

Node

B

MSAN

MSAN

Aggregation

Node

D

Standby

Active

Standby

Inter-ChassisPW

for VLL

Inter-ChassisPW

for VLL

«
...
62
63
64
65
66
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

MediaStream ConnectPlus 1000

Бренд: Avid Technology Страницы: 74

Бренд: NETGEAR Страницы: 2

Бренд: Konig Страницы: 73

ThunderLAN TNETE100A

Бренд: Texas Instruments Страницы: 179

Бренд: Caimore Страницы: 79

BladeCenter Management Module

Бренд: IBM Страницы: 184

Бренд: Qixiang Technology Страницы: 16

Бренд: TRENDnet Страницы: 10

Бренд: IBM Страницы: 34

Бренд: Quantum Страницы: 7

Бренд: BHU NETWORKS Страницы: 75

FrameSaver DSL 9788 Router

Бренд: Paradyne Страницы: 28

Бренд: Rosco Страницы: 20

Бренд: Xantech Страницы: 6

Бренд: rtd Страницы: 28

Бренд: Black Box Страницы: 62

WISENET XRN-1610

Бренд: Hanwha Techwin Страницы: 88

Бренд: Radio Shack Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды