Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 313 | Manualshive

Страница: 313 / 444

Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 313

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 313

secondary-override

Syntax

secondary-override

Context

config>card>mda>ingress>mcast-mgmt

Description

This command enables the context to configure MDA ingress multicast path-limit overrides.

The path override CLI nodes are not supported on IOM-3.

ancillary-override

Syntax

ancillary-override

Context

config>card>mda>ingress>mcast-mgmt

Description

This command enables the context to configure MDA ingress multicast path-limit overrides.

path-limit

Syntax

path-limit

megabits-per-second

no path-limit

Context

config>card>mda>ingress>mcast-mgmt>primary-override
config>card>mda>ingress>mcast-mgmt>secondary-override
config>card>mda>ingress>mcast-mgmt>ancillary-override

Description

The path-limit command is used to override the path limits contained in the bandwidth policy
associated with the MDA. The path limits are used to give the upper limit that multicast channels may
use on each path.

The path-limit commands are not supported on IOM-3.

The no form of the command removes a path limit override from an ingress multicast path and restore
the path limit defined in the bandwidth policy associated with the MDA.

Parameters

megabits-per-second —

The megabits-per-second parameter is required when executing the path-

limit command and is expressed as an integer representing multiples of 1,000,000 bits per
second.

Values

Primary-override:

1 to 2000

Secondary-override:

1 to 2000

Ancillary-override:

1 to 5000

Default

None

«
...
311
312
313
314
315
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов