Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 411

Страница: 411 / 444

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 411

vci: —

Displays the VCI values.

Values

1, 2, 5 — 65534

detail —

Provides detailed information.

MDA Values

1, 2

Output

Show Mutlilink-bundle IMA ATM Connections Output —

The following table describes

show multilink-bundle IMA ATM connections output fields.

Mutlilink-Bundle IMA ATM Connections Output Fields

Sample Output

A:NS052651098# show multilink-bundle bundle-ima-1/1.1 ima atm connections

================================================================

ATM Connections, Port bundle-ima-1/1.1

================================================================

Owner Type Ing.TD Egr.TD Adm OAM Opr

----------------------------------------------------------------

1/100 SAP PVC 2 2 up up up

================================================================

A:NS052651098#

Label

Description

Owner

Identifies the system entity that owns a specific ATM connection.

Type

Specifies the type of this multilink bundle.

mlppp —

Indicates that the bundle is of type MLPPP.

ima —

Indicates that the bundle is of type IMA group.

Ing.TD

Specifies the ATM traffic descriptor profile that applies to the receive
direction of the interface connection.

Egr.TD

Specifies the ATM traffic descriptor profile that applies to the transmit
direction of the interface connection.

Adm

ima —

Indicates that the bundle is of type IMA group.

Down —

The bundle is administratively down.

Opr

Up —

The bundle is operationally up.

Down —

The bundle is operationally down.

OAM

Indicates the OAM operational status of ATM connections.

Содержание 7750 SR OS





























































































































































































































































































































































































































































Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса

Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды