manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса, Страница: 349 / 444

Поделиться
Скачать
Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 349

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 349

SONET — 

The port is configured as SONET-SDH

MTU

The size of the largest packet which can be sent/received on the Ether-
net physical interface, specified in octets.

Admin State

Up — 

The port is administratively up.

Down — 

The port is administratively down.

Oper State

Up — 

The port is operationally up.

Down — 

The port is operationally down.

Duplex

Full — 

The link is set to full duplex mode.

Half — 

The link is set to half duplex mode.

Hold time up

The link up dampening time in seconds. The port link dampening timer 
value which reduces the number of link transitions reported to upper 
layer protocols.

Hold time down

The link down dampening time in seconds. The 

down

 timer controls 

the dampening timer for link down transitions.

IfIndex

Displays the interface's index number which reflects its initialization 
sequence.

Phy Link

Yes — 

A physical link is present.

No  — 

A physical link is not present.

Configured Mode

network — 

The port is configured for transport network use.

access — 

The port is configured for service access.

Network Qos Pol

The network QoS policy ID applied to the port.

Encap Type

Null — 

Ingress frames will not use any tags or labels to delineate a 

service. 

dot1q — 

Ingress frames carry 802.1Q tags where each tag signifies 

a different service.

Active Alarms

The number of alarms outstanding on this port.

Auto-negotiate

True — 

The link attempts to automatically negotiate the link speed 

and duplex parameters. 

False — 

The duplex and speed values are used for the link. 

Alarm State

The current alarm state of the port.

Label

Description  (Continued)

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов