manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса, Страница: 366 / 444

Поделиться
Скачать
Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 366

Show Commands

Page 366

7750 SR OS Interface Configuration Guide

ALA-12# show port 7/1/1.1.1

===============================================================================

TDM DS0 Chan Group

===============================================================================

Description        : DS0GRP

Interface          : 3/1/1.1.1

TimeSlots          : 1

Speed              : 64                      CRC                  : 16

Admin Status       : up                      Oper status          : down

Last State Change  : 04/11/2007 06:54:28     Chan-Grp IfIndex     : 589332542

Configured mode    : access                  Encap Type           : bcp-null

Admin MTU          : 1518                    Oper MTU             : 1518

Physical Link      : No                      Bundle Number        : none

Idle Cycle Flags   : flags                   Load-balance-algo    : default

===============================================================================

Traffic Statistics

===============================================================================

                                                   Input                 Output

-------------------------------------------------------------------------------

Octets                                                 0                      0

Packets                                                0                      0

Errors                                                 0                      0

===============================================================================

Port Statistics

===============================================================================

                                                   Input                 Output

-------------------------------------------------------------------------------

Packets                                                0                      0

Discards                                               0                      0

Unknown Proto Discards                                 0

===============================================================================

ALA-12#

A:ALA-48# show port 3/1/3.e3

===============================================================================

TDM Interface

===============================================================================

Description        : E3

Interface          : 3/1/3.e3

Type               : e3                      Framing              : g751

Admin Status       : up                      Oper status          : down

Physical Link      : No                      Clock Source         : loop-timed

Last State Change  : 04/11/2007 06:54:28     Port IfIndex         : 589398019

Configured mode    : access                  Encap Type           : bcp-null

Admin MTU          : 1518                    Oper MTU             : 1518

CRC                : 16                      Channelized          : none

Idle Cycle Flags   : flags                   Loopback             : none

FEAC Loop Respond  : Disabled                In FEAC Loop         : No

BERT Pattern       : none                    BERT Duration        : N/A

Err Insertion Rate : 0                       Last BERT Synched    : 0 Seconds

BERT Status        : idle                    Last BERT Errors     : 0

                                             Last BERT Total Bits : 0

Cfg Alarm          : ais los

Alarm Status       :

Subrate Mode       : none

MDL Transmit       : none

-------------------------------------------------------------------------------

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов