Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 138 | Manualshive

Страница: 138 / 444

background image

Configuring Ports

Page 138

7750 SR OS Interface Configuration Guide

DS3 path configured for PLCP mapping:

•

Supports transmit and receive of the Ax, Px and C1 bits.

•

Ignores the received Z1, Z2, Z3 octets of the PLCP frame and transmits all zeros in the Z1,
Z2, Z3 octets of the PLCP frame.

•

Ignores the received F1 octet of the PLCP frame, and transmits all zeros in the F1 octet of
the PLCP frame.

•

Samples and uses for performance monitoring received FEBE bits of G1 octet and
transmits the number of BIP-8 errors detected by the receive framer using the FEBE bits
of the G1 octet.Detects a PLCP Far End Alarm when 10 consecutive PLCP frames are
received with the RAI bit set, and transmits a set RAI bit when the local port has declared

Table 22: Alarm State Interactions

Content of the Received Signal

Status Field Values

Local
Signal

Local
Frame

Local
Payld

Local
PLCP
Framing

Far End
Framing

Far End
PLCP
Framing

Path
Sonet
Alarm
Status

Path Oper
Status

Atm
Interface
Oper
Status

PLCP
Alarm
State

Y

Y

Y

Y

Y

Y

None

Up

Up

No Alarm

Y

Y

Y

Y

Y

Prob

None

Up

Lower
Layer
Down

Far End
Alarm Rx

Y

Y

Y

Y

Prob

Prob

RDI

Down

Lower
Layer
Down

Far End
Alarm Rx

Y

Y

Y

Prob

Y

N/A

None

Up

Lower
Layer
Down

Incoming
LOF

Y

Y

Y

Prob

Prob

N/A

RDI

Down

Lower
Layer
Down

Incoming
LOF

Y

Prob

N/A

N/A

N/A

N/A

LOF

Down

Lower
Layer
Down

Incoming
LOF

AIS

N/A

N/A

N/A

N/A

N/A

AIS

Down

Lower
Layer
Down

Incoming
LOF

Prob

N/A

N/A

N/A

N/A

N/A

LOS

Down

Lower
Layer
Down

Incoming
LOF

«
...
136
137
138
139
140
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

TokenLink 3C359B

Бренд: 3Com Страницы: 4

TokenLink 3C359B

Бренд: 3Com Страницы: 8

TokenLink 3C339

Бренд: 3Com Страницы: 2

EtherLink 3C985B-SX

Бренд: 3Com Страницы: 44

Бренд: 3Com Страницы: 88

Бренд: 3Com Страницы: 2

Бренд: 3Com Страницы: 111

TokenLink 3C359

Бренд: 3Com Страницы: 4

Бренд: 3Com Страницы: 74

Бренд: 3Com Страницы: 6

Бренд: Zonet Страницы: 8

Бренд: REXROTH Страницы: 68

PowerBeam AC Gen2

Бренд: Ubiquiti Страницы: 22

HomePlug AV Ethernet Bridge PLE0200

Бренд: Abocom Страницы: 2

Бренд: XNET Страницы: 17

Turbo NAS TVS-71 Series

Бренд: QNAP Страницы: 51

Бренд: Global Sun Страницы: 39

Бренд: IEI Technology Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды