Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 219 | Manualshive

Страница: 219 / 444

background image

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 219

revert-time

Syntax

revert-time

minutes

no revert-time

Context

config>port>aps

Description

This command configures the revert-time timer to determine how long to wait before switching back
to the working circuit after that circuit has been restored into service.

A change in the

minutes

value takes effect upon the next initiation of the wait to restore (WTR) timer.

It does not modify the length of a WTR timer that has already been started. The WTR timer of a non-
revertive switch can be assumed to be infinite.

The

no

form of this command restores the default (non-revertive mode).

Default

The default is to not revert back unless the protect circuit fails or operator intervention.

Parameters

minutes —

Specify the time, in minutes, to wait before reverting back to the original working circuit

after it has been restored into service.

Values

0— 60 minutes

Default

5

switching-mode

Syntax

switching-mode

{

bi-directional

|

uni-directional

}

Context

config>port>aps

Description

This command configures the switching mode for the APS port.

Parameters

bi-directional —

Provides protection in one direction.

uni-directional —

Provides protection in both directions.

working-circuit

Syntax

working-circuit

port-id

Context

config>port>aps

Description

This command configures a physical port that will act as the working circuit for this APS group. The
working circuit port must contain only the default configuration and cannot be part of another APS
group. The working circuit must be created before the protection circuit.

When a port is a working circuit of an APS group, the configuration available under

config>port

port-id

context (including submenus) is not allowed for that port unless it is a part of the noted

exceptions.

«
...
217
218
219
220
221
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

Бренд: CAME Страницы: 19

Бренд: Patton electronics Страницы: 8

RDX QuikStation 4

Бренд: Tandberg Data Страницы: 2

Бренд: QNAP Страницы: 54

Бренд: IBASE Technology Страницы: 39

Бренд: Softing Страницы: 16

Бренд: JLCooper Electronics Страницы: 12

Бренд: Carrier Страницы: 18

Бренд: Qvis Страницы: 233

Бренд: PairGain Страницы: 76

Бренд: ICP DAS USA Страницы: 26

Vigor 3200 Series

Бренд: Draytek Страницы: 356

Бренд: Foscam Страницы: 92

Бренд: 3Com Страницы: 2

Бренд: 3Com Страницы: 8

AirProtect Enterprise Engine 6100

Бренд: 3Com Страницы: 12

Бренд: 2Wire Страницы: 20

Бренд: 3Com Страницы: 82

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды