Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 188 | Manualshive

Страница: 188 / 444

background image

Configuration Commands

Page 188

7750 SR OS Interface Configuration Guide

Because the IOM-3 integrated card does not have the capability in install separate MDAs, the
configuration of the MDA is automatic. This configuration only includes the default parameters such
as default buffer policies. Commands to manage the MDA such as

shutdown

, named buffer pool etc

will remain in the MDA configuration context.

An appropriate alarm is raised if a partial or complete card failure is detected. The alarm is cleared
when the error condition ceases.

The

no

form of this command removes the card from the configuration.

Default

No cards are preconfigured for any slots.

Parameters

card-type —

The type of IOM to be configured and installed in that slot.

Values

iom-20g, iom2-20g, iom-20g-b, iom3-xp, imm48-1gb-sfp, imm48-1gb-tx, imm8-
10gb-xfp, imm4-10gb-xfp

named-pool-mode

Syntax

[

no

]

named-pool-mode

Context

config>card

Description

This command places an IOM in the named pool mode. When in named pool mode, the system will
change the way default pools are created and allow for the creation of MDA and port level named
buffer pools. When named-pool-mode is not enabled, the system will create default ingress and
egress pools per port. When named-pool-mode is enabled, the system will not create per port pools,
instead a default network and access pool is created for ingress and egress and is shared by queues on
all ports.

Named pool mode may be enabled and disabled at anytime. Care should be taken when changing the
pool mode for an IOM as the process of changing to or from named pool mode causes an IOM reset if
MDAs are currently provisioned on the slot. If MDAs have not been provisioned at the time the
named-pool-mode or no named-pool-mode command is executed, the IOM is not reset (for example,
when the system is booting, the named pool mode command does not reset the IOM since the mode is
set prior to provisioning the IOM’s MDAs).

This command is not enabled for the ISA-AA MDA.

The

no

form of the command converts the pool mode on the IOM card to the default mode. If MDAs

are currently provisioned on the IOM, the card is reset.

fixed-bandwidth-pool-mode

Syntax

[

no

]

fixed-bandwidth-pool-mode

Context

config>card

Description

This command command controls the way that buffer space is allocated to buffer pools. In both
named pool mode and default pool mode, the available buffer space is distributed to each port and

«
...
186
187
188
189
190
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

Бренд: D-Link Страницы: 38

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 22

Бренд: D-Link Страницы: 20

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 16

Бренд: D-Link Страницы: 12

DIR-615 - Wireless N Router

Бренд: D-Link Страницы: 13

Бренд: D-Link Страницы: 124

Web Smart DES-1210-28P

Бренд: D-Link Страницы: 6

2Voice + 4SW VoIP Router DVG-1402S

Бренд: D-Link Страницы: 57

xStack Storage DSN-4000 Series

Бренд: D-Link Страницы: 23

Express EtherNetwork DI-604

Бренд: D-Link Страницы: 7

xStack Storage DSN-4000 Series

Бренд: D-Link Страницы: 97

SharePort DIR-825

Бренд: D-Link Страницы: 2

Amplifi DIR-645

Бренд: D-Link Страницы: 28

Бренд: Makita Страницы: 2

Бренд: JCG Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды