Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 299 | Manualshive

Страница: 299 / 444

Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 299

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 299

Multi-Chassis Redundancy Commands

redundancy

Syntax

redundancy

Context

config

Description

This command allows the user to perform redundancy operations.

Associated commands include the following in the

admin>redundancy

context:

force-switchover

— Forces a switchover to the standby CPM card.

now —

Switch to standby CPM.

NOTE:

Switching to the standby displays the following message.

WARNING: Configuration and/or Boot options may have changed since the last save.

Are you sure you want to switchover (y/n)?

synchronize

— Synchronizes the secondary CPM.

Values

<boot-env|config>

: keywords

Refer to the 7750 SR OS Basic System Configuration Guide.

synchronize

Syntax

synchronize

{

boot-env

|

config

}

Context

config>redundancy

Description

This command performs a synchronization of the standby CPM’s images and/or config files to the
active CPM. Either the

boot-env

or

config

parameter must be specified.

In the

config>redundancy

context, this command performs an automatically triggered standby CPM

synchronization.

When the standby CPM takes over operation following a failure or reset of the active CPM, it is
important to ensure that the active and standby CPMs have identical operational parameters. This
includes the saved configuration, CPM and IOM images.
The active CPM ensures that the active configuration is maintained on the standby CPM. However, to
ensure smooth operation under all circumstances, runtime images and system initialization
configurations must also be automatically synchronized between the active and standby CPM.

If synchronization fails, alarms and log messages that indicate the type of error that caused the failure
of the synchronization operation are generated. When the error condition ceases to exist, the alarm is
cleared.

Only files stored on the router are synchronized. If a configuration file or image is stored in a location
other than on a local compact flash, the file is not synchronized (for example, storing a configuration
file on an FTP server).

«
...
297
298
299
300
301
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов