Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 330 | Manualshive

Страница: 330 / 444

background image

Show Commands

Page 330

7750 SR OS Interface Configuration Guide

MDA Detailed Output —

The following table describes detailed MDA output fields.

Label

Description

Slot

The chassis slot number.

Slot

The MDA slot number.

Provisioned Pro-

visioned-type

The provisioned MDA type.

Equipped Mda-

type

The MDA type that is physically inserted into this slot in this chassis.

Admin State

Up —

The MDA is administratively up.

Down —

The MDA is administratively down.

Operational

State

Up —

The MDA is operationally up.

Down —

The MDA is operationally down.

Maximum port

count

The maximum number of ports that can be equipped on the MDA card.

Number of ports

equipped

The number of ports that are actually equipped on the MDA.

Transmit timing

selected

The transmit timing method which is presently selected and being
used by this MDA.

Sync Interface

timing status

Indicates the status of the synchronous equipment timing subsystem.

Network Ingress

Queue Policy

Specifies the network queue policy applied to the MDA to define the
queueing structure for this object.

Capabilities

Specifies the minimum size of the channel that can exist on the chan-
nelized MDA.

Max channel size

Specifies the maximum size of the channel that can exist on the chan-
nelized MDA.

Channels in use

Applicable for SONET and TDM MDAs only. Indicates the total num-
ber of leaf SONET paths, TDM channels and bundles on the MDA
which are presently provisioned for passing traffic.

Part number

The hardware part number.

CLEI code

The code used to identify the MDA.

Serial number

The MDA part number. Not user modifiable.

Manufacture date

The MDA manufacture date. Not user modifiable.

«
...
328
329
330
331
332
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

Бренд: D-Link Страницы: 13

DG834GT - 108 Mbps Super G Wireless ADSL Router

Бренд: NETGEAR Страницы: 2

NI WLS/ENET-9163

Бренд: National Instruments Страницы: 36

IPS Pro-Module-24C-GE-BP-TM

Бренд: Trend Micro Страницы: 3

Бренд: Idis Страницы: 20

UniFi LED ULED-AT

Бренд: Ubiquiti Страницы: 16

Бренд: TP-Link Страницы: 2

Бренд: H3C Страницы: 68

Bolide BN-NVR/NX

Бренд: GSA Страницы: 101

Бренд: Flexwatch Страницы: 13

3CRWE737A - 11Mbps Airconnect Wireless Lan PC Card...

Бренд: 3Com Страницы: 6

Westermo Ibex-RT-330-5G Series

Бренд: IBEX Страницы: 36

Бренд: Johnson Controls Страницы: 10

Бренд: Ericsson Страницы: 98

Бренд: XtendLan Страницы: 7

SmartMotion ST355

Бренд: Advantech Страницы: 51

Бренд: Pico Macom Страницы: 2

Бренд: Eaton Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды