Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 324

Страница: 324 / 444

Show Commands

Page 324

7750 SR OS Interface Configuration Guide

6/2 m1-choc12-sfp up provisioned 1

7 iom-20g up provisioned 2

7/1 m12-chds3 up provisioned 12

7/2 m1-choc12-sfp up provisioned 1

8 iom-20g up provisioned 2

8/1 m8-oc12/3-sfp up provisioned 8

8/2 m1-choc12-sfp up provisioned 1

9 iom-20g up provisioned 2

9/1 m20-1gb-sfp up provisioned 20

9/2 m4-atmoc12/3-sfp up provisioned 4

10 iom-20g up provisioned 2

10/1 vsm-cca up provisioned 6

10/2 vsm-cca up provisioned 6

A sfm-400g sfm-400g up up Active

B sfm-400g up provisioned Standby

===============================================================================

A:ALA-48#

Show Card Detail Output —

The following table describes detailed card output fields.

Label

Description

Clock source

The system's clock source.

Available MDA

slots

The number of MDA slots available on the IOM.

Installed MDAs

The number of MDAs installed on the IOM.

Part number

The IOM part number.

CLEI code

The Common Language Location Identifier (CLLI) code string for the
router.

Serial number

The serial number. Not user modifiable.

Manufacture date

The chassis manufacture date. Not user modifiable.

Manufacturing

string

Factory-inputted manufacturing text string. Not user modifiable.

Manufacturing

deviations

Displays a record of changes by manufacturing to the hardware or
software and which is outside the normal revision control process.

Administrative

state

Up —

The card is administratively up.

Down —

The card is administratively down.

Operational

state

Up —

The card is operationally up.

Down —

The card is operationally down.

Temperature

Internal chassis temperature.

Содержание 7750 SR OS





























































































































































































































































































































































































































































Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса

Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды