Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 308

Страница: 308 / 444

Configuration Commands

Page 308

7750 SR OS Interface Configuration Guide

range

Syntax

[no] range

vlan-range

Context

config>redundancy>mc>peer>mcr>ring>path-b
config>redundancy>mc>peer>mcr>ring>path-excl

Description

This command configures a MCR b-path VLAN range.

Parameters

vlan-range —

Specifies the VLAN range.

Values

[0 — 4094] — [0 — 4094]

path-excl

Syntax

[

]

path-excl

Context

config>redundancy>mc>peer>mcr>ring

Description

This command specifies the set of upper-VLAN IDs associated with the SAPs that are to be excluded
from control by the multi-chassis ring.

Default

If not specified, the default is an empty set.

ring-node

Syntax

ring-node

ring-node-name

[

create

]

no ring-node

ring-node-name

Context

config>redundancy>mc>peer>mcr>ring

Description

This command specifies the unique name of a multi-chassis ring access node.

Parameters

ring-node-name —

Specifies the unique name of a multi-chassis ring access node.

create —

Keyword used to create the ring node instance. The

create

keyword requirement can be

enabled/disabled in the

environment>create

context.

connectivity-verify

Syntax

connectivity-verify

Context

config>redundancy>mc>peer>mcr>ring>ring-node

Description

This command enables the context to configure node connectivity check parameters.

Содержание 7750 SR OS





























































































































































































































































































































































































































































Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса

Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды