Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 213 | Manualshive

Страница: 213 / 444

background image

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 213

ppp

Syntax

ppp

Context

config>port>sonet-sdh>path
config>port>tdm>ds1>channel-group
config>port>tdm>ds3
config>port>tdm>e1>channel-group
config>port>tdm>e3

Description

This command enables access to the context to configure the LCP operational parameters for a
SONET/SDH PoS link, a DS--3/E-3 port or channel, a DS-1/E-1 channel or a DS-0 channel.

Default

no ppp

compress

Syntax

compress

{

acfc

[

pfc

] |

pfc

[

acfc

]}

no compress

Context

config>port>tdm>ds1>channel-group>ppp
config>port>tdm>e1>channel-group>ppp

Description

This command enables and disables Protocol Field Compression (PFC) per RFC 1661,

The Point-to-

Point Protocol (PPP),

Section 6.5 and Address and Control Field Compression (ACFC) as per

Section 6.6.

This command is only supported on DS-1 and E-1 channel groups on ASAP MDAs.

The

no

form of the command disables the header compression.

Default

no compress

Parameters

acfc —

Specifies address and control field compression.

pfc —

specifies protocol field compression.

report-alarm

Syntax

[

no

]

report-alarm

[

ais

] [

los

] [

oof

] [

rai

] [

looped

]

Context

config>port>tdm> ds3
config>port>tdm> e3

Description

This command enables logging of DS-3 and E-3 alarms for a DS-3/E-3 port or channel.

The

no

form of this command disables logging of the specified alarms.

Parameters

ais —

Reports alarm indication signal errors. When configured,

ais

alarms are not raised and cleared.

Default

ais

alarms are issued

«
...
211
212
213
214
215
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

Бренд: D-Link Страницы: 11

Бренд: D-Link Страницы: 8

AirPlus DWL-810

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 84

Бренд: D-Link Страницы: 12

Бренд: GE Страницы: 6

Бренд: Paradyne Страницы: 20

Compshere 3000 Series

Бренд: Paradyne Страницы: 2

Бренд: Pantech Страницы: 17

Бренд: NetComm Страницы: 3

Бренд: Lorex Страницы: 186

Бренд: Vivotek Страницы: 170

Бренд: peplink Страницы: 2

Бренд: E-Lins Страницы: 113

Бренд: Z Microsystems Страницы: 51

Бренд: Active Communications Страницы: 10

Бренд: PaloAlto Networks Страницы: 28

Бренд: ZyXEL Communications Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды